ADXL343BCCZ-RL7
Product Specifications
ADXL343BCCZ-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADXL343BCCZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADXL343BCCZ-RL7: Three Axes, 3.9 mg per Code, 23 Microamps
The ADXL343BCCZ-RL7 is a three axis digital accelerometer with selectable plus and minus 2, 4, 8 and 16 g ranges, 10 to 13 bit resolution, SPI and I2C interfaces and a supply current down to 23 microamps. It is the part that puts motion sensing into a product that has to run for a year on a coin cell. Buyers arrive here when a handheld or battery powered device needs tap, free fall or activity detection without a microcontroller waking up to poll an analogue sensor.
What the part contains
A three axis MEMS sensing element with a 13 bit analogue to digital conversion chain, a digital filter, a command and data register set, and a FIFO that lets the host burst read rather than poll. The motion functions are in hardware: tap and double tap, activity and inactivity, and free fall, each with a user adjustable threshold and each mappable to either of two interrupt pins. The part speaks SPI in three or four wire mode and I2C, runs from 2.0 V to 3.6 V with an I/O supply from 1.7 V to the sensor supply, and survives 10,000 g of shock. It is a 3 mm by 5 mm by 1 mm LGA and rated from -40 C to +85 C.
Key parameters
| Parameter | Value |
|---|---|
| Axes | Three, digital output |
| Ranges | Plus and minus 2, 4, 8 and 16 g, selectable |
| Resolution | 10 to 13 bit |
| Scale factor | 3.9 mg per code at every range |
| Supply current | Down to 23 microamps |
| Supply voltage | 2.0 V to 3.6 V |
| I/O voltage | 1.7 V to sensor supply |
| Interfaces | SPI three and four wire, I2C |
| Motion functions | Tap, double tap, activity, inactivity, free fall |
| Interrupts | Two pins, independently mappable |
| Shock survival | 10,000 g |
| Temperature range | -40 C to +85 C |
| Package | LGA, 3 mm by 5 mm by 1 mm |
What the numbers mean on a board
The scale factor stays at 3.9 mg per code across every range because the resolution rises with the range: 10 bit across a 4 g span is 3.91 mg, and 13 bit across a 32 g span is the same 3.91 mg. That is deliberate, and it means a change of range does not change the firmware scaling constant. It also means the 16 g range is not a way to get finer resolution on a small signal; it is a way to keep the sensor from clipping when the product is dropped.
At 23 microamps the part draws 0.201 amp hours over a year, which is a fifth of a small coin cell. In a product that also has a radio, the accelerometer is not the load that matters; the important number is how often the host wakes up. The hardware motion functions exist so the host can sleep until an interrupt arrives, and the FIFO exists so that a burst of samples is read in one transaction instead of one interrupt per sample. A product that polls the sensor at 100 Hz has thrown away the reason to buy this part.
3.9 mg per code also defines what the part can and cannot do as a tilt sensor. Near horizontal, one degree of tilt produces 17.5 mg of gravity component, which is 4.5 codes, so a static tilt measurement is good to a fraction of a degree after averaging. Near vertical the same degree produces almost no change in the horizontal axes, so tilt accuracy is a function of orientation and the part needs a calibration constant per axis rather than a single sensitivity figure.
Where it is used
- Handheld instruments with tap or orientation input
- Battery powered asset trackers that wake on motion
- Free fall detection in disk drives and portable equipment
- Activity and inactivity monitoring in wearable and medical devices
- Anti tamper detection in meters and enclosures
Sourcing notes and next step
This is a high volume consumer and industrial part, and the buying risk is the opposite of an obsolete RF device: the risk is a broker reel at a price that looks too good. The LGA is 1 mm tall and easy to reflow with voids under the pads, and a part that has been stored open will show an offset shift after reflow that looks like a calibration failure. Ask for the seal date, the moisture level and the reel label, and keep the RL7 packing on the purchase order so the pick and place program does not have to be changed.
Sensor and converter combinations for a monitoring board are collected in BOM shortage recovery, and parts with a long production commitment are listed on the obsolete and long life hub. The rest of the catalogue is on the analog and mixed signal family page. Send the range, the supply voltage and the quantity and we confirm stock and seal date the same day.
Request Quote — In Stock, 100% New & Original, Full Warranty