Contact Us

AD9709ASTZ

Brand: Analog Devices
Analog Devices AD9709ASTZ is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD9709ASTZ — Analog & Mixed-Signal ICs | Superb Automation

AD9709ASTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD9709ASTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD9709ASTZ: Two 8 Bit DACs at 125 MSPS for an I and Q Pair

The AD9709ASTZ is a dual 8 bit digital to analog converter with a 125 MSPS update rate, two matched current output cores, an on chip 1.2 V reference and a 20 mA full scale current. It is built for I and Q transmit paths, where two converters on one die matter more than either converter's absolute accuracy because gain and offset matching set the sideband rejection. Buyers reach this page from base station, quadrature modulation and 3D ultrasound front ends.

What the part contains

Two 8 bit DAC cores with separate write inputs and separate clocks, so the two ports can be driven independently or from a single interleaved data stream. In interleaved mode the input is demultiplexed back into I and Q and updated at half the input data rate. Spurious free dynamic range is 66 dBc with a 5 MHz output, gain matching between the two DACs is 0.1 percent and offset error is better than 0.02 percent. Full scale current is nominally 20 mA per DAC, set by one resistor for both or by two resistors independently. The part runs from 3.3 V or 5 V and dissipates 380 mW, in a 48-lead LQFP.

Key parameters

ParameterValue
Resolution8 bit, two channels
Update rate125 MSPS
SFDR at 5 MHz output66 dBc
Gain matching between channels0.1 percent
Offset errorBetter than 0.02 percent
Full scale current20 mA nominal
Reference1.2 V internal
Data interfaceDual port or interleaved
Supply3.3 V or 5 V
Power380 mW
Package48-lead LQFP

What the numbers mean on a board

Twenty milliamps across 256 codes is 78.1 microamps per code, so the smallest current step is 0.39 percent of full scale. Gain matching of 0.1 percent between the two channels is 0.26 of a code, which sets the quadrature amplitude balance and therefore the sideband suppression: a 0.1 percent amplitude error alone holds the unwanted sideband near 60 dB below the wanted one, and phase error adds to that. That is why the matching figure, not the resolution, is the first line of this data sheet.

At 125 MSPS the Nyquist point is 62.5 MHz, so a 20 MHz band is comfortably inside the first Nyquist zone and the reconstruction filter only has to remove images starting at 105 MHz. Spurious free dynamic range of 66 dBc at a 5 MHz output is about a factor of 2000 between the carrier and the largest spur, which in an 8 bit converter is set by the segmentation of the current sources rather than by the 8 bit quantisation floor of 49.9 dB.

Three hundred and eighty milliwatts is 3 mW per MSPS, which in a 48-lead LQFP is a package that runs warm but not hot. The 20 mA full scale current into a 50 ohm load develops 1 V, so the output compliance range of the current cells is what limits the termination resistor: 20 mA into 100 ohm would need 2 V of headroom that a 3.3 V supply does not have.

Where it is used

  • Base station transmit paths with digital predistortion
  • Quadrature modulation in radio transmitters
  • 3D ultrasound beamformers
  • Direct digital synthesis instruments
  • Arbitrary waveform generators with two channels

Output network, gain resistor and interleaved timing

The current outputs want a transformer or a differential amplifier, not a resistor to ground on each leg, if the full 20 mA is to be used within the compliance range. A 50 ohm resistor on each output develops 1 V at full scale and leaves 2.3 V of headroom on a 3.3 V supply, which is enough for the current sources but leaves little for a signal that swings. A 1 to 1 transformer with a 50 ohm load gives the same 1 V with better common mode behaviour and no loss of headroom.

Full scale current is set by one resistor for both channels or independently by two, and the 0.1 percent matching between channels only holds when both use the same resistor value and the same temperature. If the two channels are set independently, the matching depends on the two resistors, so use a pair from the same package. In interleaved mode the input data is demultiplexed and the two DACs update at half the input rate, which halves the clock rate at the pins but not the update rate at the outputs.

Sourcing notes and next step

The order code is the tray or the reel of the 48-lead LQFP, and the family is pin compatible across 8, 10, 12 and 14 bit versions, which makes a mixed reel a real risk at goods in. Check the resolution suffix on the label. Stock on this generation is thinning as boards move to higher speed parts, so a lifetime buy is often the cheaper decision than a board change.

Converter pairs for a transmit chain are compared on the ADC and DAC cross reference page, and complete modulator and converter sets for a radio build are in BOM shortage recovery. The rest of the catalogue is on the analog and mixed signal family page. Send the update rate, the output band and the quantity and we confirm stock and date code.

Request Quote — In Stock, 100% New & Original, Full Warranty