ADN8834ACBZ-R7
Product Specifications
ADN8834ACBZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADN8834ACBZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADN8834ACBZ-R7: A 1.5 A TEC Controller with One Inductor and Two Chopper Amplifiers
What this part is
The ADN8834 drives a thermoelectric cooler from a single inductor. Inside the package there is an H bridge of low on resistance MOSFETs, a linear stage that works with a pulse width modulated stage, two zero drift chopper amplifiers and a 2.50 V reference. The two amplifiers take the thermistor or resistance temperature detector bridge and close a proportional integral derivative loop around the target temperature, so a laser diode or a passive optical component mounted on the cooler is held without a separate controller chip and without an external sense resistor.
Heating and cooling current limits are set independently, the maximum cooler voltage is programmable, and the switching stage runs at 2.0 MHz with an external synchronisation input, which keeps the switching tone out of the band a photodiode front end cares about. Both the cooler voltage and the cooler current can be monitored, and a temperature lock indicator tells the host when the loop has settled. The body is a 25 ball wafer level chip scale package of 2.5 mm by 2.5 mm, or a 24 lead LFCSP of 4 mm by 4 mm, and the part is qualified to AEC-Q100.
Published figures that matter to a buyer
| Output current | 1.5 A |
| Power stage | single inductor, integrated MOSFETs |
| Switching frequency | 2.0 MHz, with external synchronisation |
| Current limits | independent heating and cooling settings |
| Maximum cooler voltage | programmable |
| Sense resistor | not required |
| Amplifiers | two zero drift, rail to rail chopper types |
| Sensor types | thermistor or resistance temperature detector |
| Reference | 2.50 V, 1 percent |
| Monitoring | cooler voltage and current, temperature lock indicator |
| Body | 25 ball WLCSP 2.5 mm by 2.5 mm, or 24 lead LFCSP 4 mm by 4 mm |
| Qualification | AEC-Q100 |
Where the headline numbers stop
The 1.5 A is a current rating and not a power rating. Into a cooler that drops 2 V it is 3 W of output and about 1.2 W of loss in the bridge; into a 2.5 V cooler it is 3.75 W of output, and the loss rises with the square of the current. That is why the maximum cooler voltage is programmable: the point of that setting is to stop the loop from asking for a voltage the cooler and the bridge cannot take when the loop is saturated at start up, which is the moment a cooler is most likely to be damaged.
The 2.0 MHz switching period is 500 ns, so the inductor and the output capacitance are chosen against a small period and a small ripple rather than against a low frequency converter. The external synchronisation input exists so that several controllers can share one clock and so that the switching tone can be placed where the measurement does not look.
The 2.50 V reference at 1 percent is 25 mV, and the loop accuracy has to be read against the sensor rather than against the reference: a thermistor with a 1 percent tolerance and a 3,900 ppm per degree C coefficient moves about 0.26 percent per degree C, so 25 mV of reference error is worth roughly 0.1 degree C while a 1 percent sensor tolerance is worth several degrees. The reference is not the limiting term, and money spent on it instead of on the sensor is money in the wrong place.
Applications where it fits
- Laser diode and pump laser temperature control in optical transceivers and instrumentation.
- Cooled photodetectors and image sensors where dark current has to be held.
- Compact analysers and gas sensors that need a stable optical bench temperature.
- Automotive optical and sensor modules, where the AEC-Q100 grade is a requirement rather than a preference.
Two questions buyers ask
Why one inductor instead of two? A single inductor H bridge needs one magnetic part and one set of switches, which is what makes a 2.5 mm by 2.5 mm body possible. The cost is that heating and cooling share the same magnetic path, so the ripple current differs between the two directions and the independent current limits exist to keep both directions inside the same hardware.
Can the loop be run open at start up? The programmable maximum voltage is what protects the cooler while the loop pulls in. A start up with no limit asks for whatever the error amplifier demands into a cooler that is at ambient, and the current limit alone will not stop the voltage from reaching the rail. Both settings belong in the initialisation sequence, not only in the steady state tuning.
Sourcing notes and next step
ADN8834ACBZ-R7 is the 25 ball wafer level package on tape and reel; the LFCSP version is a different order code and a different footprint. Because the two bodies are not interchangeable on a board, a quote should always name the package letter as well as the family number. The power management cross reference page sets out the fields to compare across a controller substitution, the medical device components page covers traceability for instrument builds, and the analog and mixed signal IC family page lists the rest of the power line.
Request Quote — In Stock, 100% New & Original, Full Warranty