Contact Us

TJA1040T/CM,118

Brand: NXP Semiconductors
NXP Semiconductors TJA1040T/CM,118 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1040T/CM,118 — MCU & Embedded Processors | Superb Automation

TJA1040T/CM,118

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1040T/CM,118 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1040T/CM,118: SO8 CAN transceiver with standby and SPLIT

TJA1040T/CM,118 is a second generation high speed CAN transceiver with a standby mode and a SPLIT output in the TJA1040 high speed CAN transceiver line, described by 2003 Oct 14 product specification. It sits between a CAN protocol controller and the two wire bus and adds two things over the TJA1050 it was derived from: a standby mode that wakes on bus activity and a SPLIT output that holds the midpoint of a split termination at half the supply. Both matter in a node that has to stay reachable while the rest of the board is powered down.

Order code and package

Order codeTJA1040T/CM,118
Variant function on pin 5SPLIT output; there is no VIO pin and no enable pin
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898 (the original standard, not the 2016 revision)
Maximum data rateup to 1 Mbaud classical CAN
Supply voltage on VCC4.75 to 5.25 V
Logic supply on VIOnot present
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
Datasheet2003 Oct 14 product specification

Electrical parameters that decide the application

Bus fault voltageminus 27 to plus 40 V on CANH, CANL and SPLIT with no time limit
Supply currentStandby 5 to 15 microamps; normal mode recessive and dominant currents are not tabulated in this document
Electrostatic dischargeplus or minus 6 kV human body model on CANH, CANL and SPLIT, plus or minus 4 kV on every other pin
Thermal resistance145 K/W junction to ambient in the SO8 body, 50 K/W junction to solder point
Wake and diagnostic pinsSTB input selects normal or standby, SPLIT output biases the recessive level, no INH and no error pin
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsinputs compatible with 3.3 V and 5 V devices per the feature list
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

The document is dated 2003 and names ISO 11898 without a revision, so it predates ISO 11898-2:2016 and carries no loop delay symmetry figures. A 500 kbit/s classical network is covered; a 2 Mbit/s or 5 Mbit/s CAN FD data phase is not, and no amount of board care changes that, because the parameter does not exist in this document.

The propagation delay TXD to RXD is given as 40 to 255 ns. At 1 Mbaud one bit is 1000 ns, so the spread alone is 21.5 percent of a bit, and at 500 kbit/s it is 10.8 percent. That is a ceiling statement rather than a bit timing budget, and it is the reason a network built on this part keeps a sample point near 80 percent.

Standby current is 5 to 15 microamps. Across a year that is 43.8 to 131.4 mAh, which is small against a 60 Ah battery and larger than the self discharge of a coin cell, so the standby figure only pays off on a vehicle battery and not on a battery powered instrument.

The SPLIT output is there to hold the recessive level of a split termination at half the supply, and the two termination resistors still set the differential load. A board that copies a split termination from a TJA1042 board and leaves the SPLIT pin floating loses the benefit and keeps the cost of the extra capacitor.

Bus pins stand minus 27 to plus 40 V with no time limit. That covers a 12 V system with load dump clamps and a short to battery, and it does not cover a 24 V rail: 27 V is inside a 24 V system at plus 12.5 percent only, so a 24 V application belongs on the 58 V parts in this family.

Electrostatic discharge is quoted as plus or minus 6 kV human body model on CANH, CANL and SPLIT and plus or minus 4 kV on the other pins. IEC 61000-4-2 is not named, so a connector exposed bus still needs its own transient suppressor, and the 6 kV figure should not be read as a system level rating.

Pin compatibility with the TJA1050 is real but pin 5 changes job: it is the silent mode input on the TJA1050 and the SPLIT output here. A board that ties pin 5 to ground on the older part would short a driven output on this one, so the substitution has to be checked against the pin function and not against the package drawing.

Where this order code fits

It is the part that shows up on boards drawn between 2003 and 2010, and it is still bought for repair and for running changes where the network stays at 500 kbit/s. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is TJA1040T a drop in replacement for the TJA1050? Not without a check on pin 5. The package and the bus pins match, but pin 5 is the silent mode input on the TJA1050 and the SPLIT output on the TJA1040, so the net that drives or grounds pin 5 has to be removed before the swap.

Does it carry a CAN FD data phase? No. The 2003 document has no loop delay symmetry parameters and names ISO 11898 without a revision, so the timing needed above 1 Mbit/s is not specified for this part.

What is the standby current over temperature? 5 microamps typical and 15 microamps maximum, which is 131.4 mAh across a year at the maximum figure.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.