Contact Us

TPS81256SIPR

Brand: Texas Instruments
Texas Instruments TPS81256SIPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS81256SIPR — Power Management & Signal Chain | Superb Automation

TPS81256SIPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS81256SIPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS81256SIPR: the 3 W step-up module that sits beside a battery connector

TPS81256SIPR is a complete 5 V step-up power module rather than a controller that needs an inductor next to it. Inside the 9-pin MicroSiP body sit the synchronous boost regulator, the inductor and the input and output capacitors, and SLVSAZ9D prints that the finished solution needs one 4.7 microfarad 16 V X5R capacitor in an 0603 case on the output and nothing else in the power path. The module measures 2.925 mm by 2.575 mm with a 1.0 mm maximum profile, and the total solution covers less than 9 square millimetres of board.

The string on our page is the SIPR tail, which the vendor addendum prints as the uSiP nine-pin body on a 3000 piece large reel. The family has a SIPT twin on a 250 piece small reel, and the only thing that separates them is the carrier and the reel size, not the silicon. A prototype line that wants a few dozen pieces is therefore asking for a partial reel of the R tail rather than for a different device.

The numbers below come from SLVSAZ9D, revised February 2018, and from the orderable addendum at the back of that document. They are the ones that decide whether this module fits a given product: the 550 mA output at 3.3 V input, the 150 mA ceiling once the input rises to the output level, the 43 microamp quiescent current in power save mode, and the moisture level that decides how the reel is stored before reflow.

What the order code sits on

Functionsynchronous step-up converter module with integrated inductor and capacitors
Input range2.5 V to 5.5 V on VIN
Outputfixed 5.0 V, no external feedback divider
Output current550 mA or more at 5.0 V out with 3.3 V or more in
Output powermore than 3 W across a full single cell Li-Ion range
Switching frequency4 MHz quasi constant in PWM, pulse frequency modulation at light load
Peak efficiency91 percent at 4 MHz
DC accuracyplus or minus 2 percent total over line, load and temperature
Quiescent current43 microamps typical in power save mode
Shutdown currentunder 1 microamp typical, with true load disconnect
PackageMicroSiP, 9 pins, 2.925 mm by 2.575 mm, 1.0 mm maximum height
External partsone 4.7 microfarad 16 V X5R output capacitor in 0603
Absolute maximumminus 0.3 V to 6 V on VIN, VOUT and EN
Input current limit1.05 A continuous average into VIN, 1.3 A pulsed
Operating ambientminus 40 to plus 85 degrees in the electrical tables
Junction and storageminus 40 to plus 150 degrees junction, minus 55 to plus 125 degrees storage

Five volts out of one Li-Ion cell

The module regulates a fixed 5.0 V and is specified to deliver 550 mA or more once the input reaches 3.3 V. On a single cell that is the part of the discharge curve between a fresh pack and roughly the last third of its capacity, so a product powered this way sees full output current for most of a charge and then a reduced ceiling as the cell falls toward 3.0 V. The boost loop keeps regulating down to 2.5 V in, which is below the usual cutoff of a phone or instrument pack, so the practical limit is the protection circuit of the cell rather than the converter.

At 4 MHz the inductor inside the package is small, and the price of that is a switching loss that shows up as a small drop in efficiency at heavy load. The data sheet prints 91 percent peak, and the efficiency curves in the typical characteristics section fall away at both ends: at very light load the part is in pulse frequency modulation and the quiescent current of 43 microamps dominates, while at the top of the current range the conduction and switching terms both climb. A product that spends its life at 100 mA sees the light load end of those curves, not the headline number.

True load disconnect in shutdown is the feature that matters when the 5 V rail feeds a connector a user can touch. With the enable pin low the module breaks the path from input to output instead of leaving the body diode conducting, so an accessory plugged into a switched off product does not see the battery through the boost stage. The enable pin must be terminated and must never be left floating, which is a line worth putting on an assembly note rather than trusting to a pull-down that may be far from the pad.

When the input is already above the output

A boost converter cannot regulate below its input, and this module handles that by sliding in and out of zero duty cycle operation rather than by jumping between modes. When the input is at or above 5.0 V the output is held as close to regulation as the topology allows, and in that state the output current capability is limited to roughly 150 mA. That number is the one that catches people out on a USB input: a product that works from a 3.7 V cell at 550 mA and is then plugged into a 5 V source does not deliver 550 mA from that source, it delivers about 150 mA, and a load that draws more will pull the rail down until the source and the load settle somewhere lower.

For a battery powered instrument the case is common. The same 5 V rail feeds an audio amplifier or a USB port, and during charging the input rises above 5 V while the load stays connected. The rail then sits at whatever the input minus the drop is, the module is not boosting, and the current available is the 150 mA figure. A build that needs full current while charging has to look at a buck-boost stage instead, and that is a different family with a different pin count.

The one capacitor that decides the ripple

Because the inductor and the input capacitor are inside the package, the output capacitor is the only component a buyer chooses, and it carries the whole loop. The data sheet asks for 4.7 microfarads, 16 V, X5R, in an 0603 case. The 16 V rating is not decoration: a 6.3 V part in the same case loses most of its capacitance under a 5 V bias, and a 4.7 microfarad X5R at 6.3 V can measure closer to 1.5 microfarads in circuit, which moves the ripple and the transient response away from the published curves.

The second thing that matters is the distance from the capacitor to the output pads. At 4 MHz the loop between the module output and the capacitor is short enough that a few millimetres of track add inductance which the control loop sees as extra series impedance. The vendor arrangement in the data sheet puts the capacitor immediately beside the VOUT pads on the same layer, and a build that moves it to the other side of the board through two vias will show more ripple at the same load than the curves promise.

Load transient behaviour is where the module is strongest, and the reason is the 4 MHz operating point combined with the internal inductor. The control loop reacts within a few switching cycles, so a load step from 10 mA to 400 mA moves the rail by tens of millivolts rather than by hundreds. That behaviour is what a camera flash, a radio transmit burst or a motor start needs, and it is the argument for paying for a module instead of building a discrete boost around a controller.

Assembly in a one millimetre profile

The body is a land grid array style module with nine pads, and the pads carry the switch node as well as the supply and ground, so paste volume is the variable that decides yield. The addendum prints moisture level 2 with a one year floor life, which means a reel that has been open for a year needs a bake before reflow and a reel that has been open for a week does not. An assembly line that stores this class of part in a dry cabinet and writes the seal date on the label has the record a customer audit asks for; a line that leaves the reel on an open shelf for months will see a small number of parts with delamination that reads as an open circuit after reflow.

The 1.0 mm maximum height is what allows the module to sit under a shield can or behind a display, and it also means the part is not a candidate for a socket. Rework is done with hot air from the back of the board or with a dedicated rework nozzle, and the pads that carry the inductor are larger than the signal pads, so a rework profile written for a 0402 passive will not transfer heat into them evenly. The part marking the addendum prints for the SIPR row is TT, which is the only marking that distinguishes the reel part from the small reel twin once the reel label is gone.

Carriers and what the addendum prints

TPS81256SIPRuSiP, 9 pads, 3000 pieces on a large reel, active
TPS81256SIPTsame body, 250 pieces on a small reel
RoHSRoHS and Green on both rows
Lead finishthe addendum prints the SIP rows without a separate finish column value
Moisture levelLevel-2-260C-1 YEAR, one year floor life
Operating temperatureminus 40 to plus 125 degrees on the addendum row
Part markingTT
Datasheet revisionSLVSAZ9D, revised February 2018

The temperature line is worth a second look because the two places in the same document disagree. The absolute maximum table prints an operating ambient of minus 40 to plus 85 degrees, while the addendum row prints minus 40 to plus 125 degrees. The higher number is the junction grade that the reel row is qualified to; the electrical tables are written against the 85 degree ambient. A product that runs the module at 105 degrees ambient is outside what the electrical tables cover even though the order line says 125, and a thermal measurement on the finished board is the only way to know where the part actually sits.

Where the module fits and where it does not

The part fits products that need one 5 V rail at a few hundred milliamps from a single cell, that have very little board area, and that cannot afford an inductor selection exercise. Handheld instruments, body worn monitors, portable audio, USB on the go adapters and camera modules are the applications the vendor lists, and the common thread is a 5 V load that is a few watts at most with a battery behind it. When the load needs more than 3 W the module is out of range regardless of the input; when the input is a 12 V rail the part is the wrong topology entirely.

The other case this part serves is the second source case. A product built around a discrete boost converter with a controller, an inductor and a compensation network carries four or five part numbers that all have to be in stock at the same time. Replacing that with a module removes the inductor and the compensation parts from the bill of materials and removes the tuning step from the build. When a customer sends a list of boosts they can no longer buy, the work starts from the input range, the output voltage and the current at that voltage rather than from the part number, and the workflow on our power management cross reference page lists what to compare before a sample is ordered. If the original string has already gone end of life, the obsolete part cross reference hub covers the case where the replacement has to be found rather than merely checked.

Lead time is the other reason a buyer arrives at this page. A module that is on a 3000 piece reel and stocked in distribution is a two week part in most quarters, while a discrete boost with an 0603 inductor can be a sixteen week part when the inductor is the constrained item. The component lead time solutions page covers what can be done short of a board change.

Questions buyers ask before a first order

Does this module work from a 5 V USB input? It works, but not at 550 mA. With the input at or above the 5.0 V output the current capability drops to roughly 150 mA, so a load that needs more has to be rated against that figure.

Can the output be set to 3.3 V? Not on this string. The output is fixed at 5.0 V with no feedback pin brought out, and a 3.3 V rail needs a different member of the family or a different converter.

How much board area does the finished solution need? Under 9 square millimetres including the output capacitor, which is the number the vendor prints and the one to use when the module is compared with a discrete boost that needs an inductor, two capacitors and a compensation network.

What has to be on the purchase order besides the part number? The reel size, because the R and T tails are the same silicon on different carriers, and the moisture level handling, because a one year floor life is shorter than the shelf life of a reel that a distributor has already opened.