Contact Us

LT1037IS8#PBF

Brand: Analog Devices
Analog Devices LT1037IS8#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT1037IS8#PBF — Analog & Mixed-Signal ICs | Superb Automation

LT1037IS8#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT1037IS8#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT1037IS8#PBF: 3.8 nV Noise, Provided the Gain Never Falls Below Five

The LT1037IS8#PBF is the decompensated member of the LT1007 family: a precision bipolar operational amplifier with 3.8 nV per root hertz noise at 1 kHz, 25 uV maximum offset voltage, 0.6 uV per degree C maximum drift, 117 dB minimum common mode rejection and a 60 MHz gain bandwidth product. The compensation capacitor on the die is smaller than the one on the unity gain stable LT1007, which is what buys the bandwidth, and the price of that is a closed loop gain of at least 5 for stable operation. The order code reads I for the industrial grade, S8 for the SO-8 package and PBF for lead free.

What the headline numbers become in a circuit

A 60 MHz gain bandwidth product at the minimum stable gain of 5 is 12 MHz of closed loop bandwidth, and at a gain of 10 it is 6 MHz. The 11 V per microsecond minimum slew rate limits a 10 V peak to peak sine to about 350 kHz regardless of the small signal figure, so a stage that has to deliver full scale at high frequency is limited by slew rate and not by gain bandwidth. Both numbers belong in the budget, and quoting only the 60 MHz is how a product ends up 30 times short of its target at full amplitude.

Noise at 1 kHz3.8 nV per root hertz guaranteed, 4.5 nV at 10 Hz
Low frequency noise60 nV peak to peak, 0.1 Hz to 10 Hz, typical
Offset voltage25 uV maximum, 10 uV typical
Offset drift0.6 uV per degree C maximum, 60 uV over 100 C
Gain bandwidth60 MHz, stable at a closed loop gain of 5 or more
Closed loop bandwidth at gain 512 MHz
Slew rate11 V per us minimum, 350 kHz at 10 V peak to peak
Common mode rejection117 dB minimum, 14.1 uV of error at a 10 V common mode
Open loop gain7 million into 2 kohm, 3 million into 600 ohm
Package8-lead SO-8, industrial temperature

The noise figure is worth putting in context. A 400 ohm resistor at room temperature produces 2.57 nV per root hertz, so the amplifier's 2.5 nV wideband figure is quieter than the resistor a microphone preamplifier would be built around. Integrated over 100 kHz the 3.8 nV becomes 1.2 uV rms, and over 1 MHz it becomes 3.8 uV, which is why the part is paired with bandwidth limiting rather than left open. The 60 nV peak to peak flicker noise over the 0.1 Hz to 10 Hz band is 0.04 percent of a 16 bit least significant bit on a 10 V span, so the low frequency end is not what limits a 16 bit measurement: drift and the reference are.

Gain, offset and the closed loop consequences

At a gain of 5 the 25 uV offset appears as 125 uV at the output, and the 0.6 uV per degree C drift becomes 60 uV over a 100 degree swing, amplified by the same 5. Neither figure is a problem for a 16 bit converter on a 10 V span, where one least significant bit is 153 uV, but both are problems for a 20 bit converter, and no amount of chopping the amplifier fixes the drift of the resistors around it. The part is a low noise front end, not an instrumentation amplifier; the gain resistor tolerance and its temperature coefficient become the error terms once the amplifier is this quiet.

The decompensation also changes the feedback network. At a gain of 5 the feedback factor is a fifth, so the noise gain seen by the amplifier is 5, and a capacitor across the feedback resistor is what sets the bandwidth and the peaking. A stage that is stable at a gain of 5 on a bench can ring when the source impedance rises, because the noise gain at high frequency is set by the source capacitance and the feedback network rather than by the signal gain. Adding the feedback capacitor and checking the response with the real source impedance is part of using this part, not an optional refinement.

Two questions buyers ask

Can it be used as a unity gain buffer?
No. The part is decompensated and is only stable at a closed loop gain of 5 or more. For a follower, the compensated LT1007 in the same family is the correct order code, at a lower bandwidth. Substituting the decompensated part into a follower socket produces an oscillator that looks like a noise problem on a scope.

Does a lower noise part exist in the same footprint?
The family itself is the low noise option, so the useful question is the source impedance. Below a few hundred ohms the amplifier noise dominates and this part is at the floor; above a few kilohms the resistor noise dominates and a quieter amplifier buys nothing. That is the calculation to run before paying for a lower noise grade.

Ordering and supply

The LT1037IS8#PBF is the industrial temperature, SO-8, lead free code. Cross references fail on stability rather than on noise, because a unity gain stable part with similar noise can be dropped into a gain of 5 stage and work, while this part cannot be dropped into a follower. The replacement also has to match the pinout of the compensated sibling if the board was laid out for the family.

We hold and source this family for production quantities and for repair lots. Start from the family page for analog mixed signal ICs, check a proposed alternative against the amplifier cross reference, and when a second source is proposed for an existing board the pin and specification comparison in pin to pin cross reference is where the stability difference shows up.

Request Quote — In Stock, 100% New & Original, Full Warranty