LT1930AES5#TRMPBF
Product Specifications
LT1930AES5#TRMPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1930AES5#TRMPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT1930AES5#TRMPBF: 12 V at 250 mA From 5 V, and the Peak Current Behind It
The LT1930AES5#TRMPBF is the 2.2 MHz member of the LT1930 family: a step-up current mode converter with a 1 A, 36 V internal switch in a 5-lead ThinSOT package. The input range is 2.6 V to 16 V, the output can reach 34 V, shutdown current is under 1 uA and the switch saturation voltage is 400 mV at 1 A. The order code reads A for the 2.2 MHz option, ES5 for the 5-lead SOT-23 and TRMPBF for tape and reel, lead free. The family is pin-for-pin compatible with the LT1613, which is why it turns up as a straight replacement in supplies that need more output current from the same small outline.
Duty cycle and the on time at 2.2 MHz
In a boost converter the duty cycle is one minus the input divided by the output. From 5 V to 12 V that is 58.3 percent, and at 2.2 MHz the period is 454 ns, so the switch is on for 265 ns in every cycle. From 3.3 V to 5 V the duty falls to 34 percent and the on time to 154 ns. The relevant limit at the other end is the maximum duty cycle, which appears when the input sags: from 3 V to 12 V the duty is 75 percent and the part is working near the edge of its range, which is exactly the condition a battery-powered product meets at end of discharge.
| Topology | Current mode step-up, 1 A 36 V internal switch |
| Input range | 2.6 V to 16 V |
| Switching frequency | 2.2 MHz (LT1930A), 1.2 MHz (LT1930) |
| Output examples | 12 V at 250 mA from 5 V, up to 34 V |
| Duty at 5 V to 12 V | 58.3 percent, 265 ns on time |
| Switch saturation at 1 A | 400 mV |
| Shutdown current | Under 1 uA |
| Package | 5-lead ThinSOT, 1 mm tall |
Input current is the number that limits the output
Twelve volts at 250 mA is 3 W. At 85 percent efficiency the input is 3.53 W, which is 706 mA from a 5 V rail. With a 4.7 uH inductor the ripple at that duty is 0.282 A, so the peak through the switch is 0.847 A against the 1 A rating, a margin of about 150 mA. That margin disappears if the inductor is reduced for board area or if the input rail is at its low limit, because the input current rises as the input voltage falls for the same output power. At 4 V in the same 3 W output needs 883 mA of average input current before any ripple is added.
The switch loss is worth putting next to the efficiency figure. A 400 mV saturation at 1 A means 0.34 W of conduction loss at 0.85 A, which is 9.6 percent of the 3.53 W input. That is why the part is specified with a low saturation switch rather than only with a current rating, and why a substitute with the same 1 A figure but a higher saturation voltage runs hotter at the same output.
Where the ceiling matters
The 36 V switch rating and the 34 V output ceiling leave 22 V of headroom above a 12 V output, which is enough for a 24 V bias rail and for the higher voltage needed by a tuning or avalanche photodiode supply. Above 34 V the topology has to change rather than the part, and a flyback or a transformer-coupled stage is the next step. The same switch also supports SEPIC, which is why the family is used to hold a 5 V rail from four alkaline cells, an input that crosses the output voltage as the cells discharge.
Two questions buyers ask
Is 250 mA at 12 V available from a 5 V input at any temperature?
On paper the peak switch current is 0.847 A with a 4.7 uH inductor, so yes at room temperature. The peak rises as the input falls and as efficiency drops, so the combination has to be checked at the minimum input and the maximum ambient, not at the nominal 5 V.
What is the difference between the LT1930 and the A version?
Switching frequency and therefore inductor size. The 1.2 MHz part uses a larger inductor; the 2.2 MHz part allows a smaller one and gives the 12 V at 250 mA example from 5 V. Package, pinout and switch rating are shared, so the choice is made on board area and on the switching frequency the rest of the system can tolerate.
SEPIC, and the input that crosses the output
A SEPIC stage holds its output whether the input is above or below it, which is why the family is used with four alkaline cells: a fresh set is 6 V and a discharged set is below 4 V, and a plain boost would drop out somewhere in the middle. From 4.5 V to 5 V the duty is 10 percent, from 3.6 V it is 28 percent, and the switch and the coupled inductor have to be chosen for the worst case rather than the nominal. In that configuration the vendor quotes 5 V at 300 mA, which is below the 480 mA available in a plain boost from 3.3 V because the SEPIC topology carries current in two windings.
The 36 V switch rating is what allows the same part to reach 24 V and, with a coupled inductor, to produce a negative rail as well. Above 34 V the topology has to change rather than the part, and a flyback or a transformer coupled stage is the next step. What does not change is the control loop: constant frequency, internally compensated, so the output noise stays predictable across those configurations.
Ordering and supply
The LT1930AES5#TRMPBF is the 2.2 MHz option in the 5-lead SOT-23, tape and reel. The frequency letter sits immediately after the base number and is the field most often dropped in a cross reference, which produces a part that fits the board and switches at the wrong rate.
We hold and source this family for production and repair quantities. Start from the family page for analog mixed signal ICs, check a proposed alternative against the power management cross reference, and if the schedule is the constraint rather than the price, the lead time options page sets out what can be pulled forward.
Request Quote — In Stock, 100% New & Original, Full Warranty