Contact Us

TPS7A9001DSKR

Brand: Texas Instruments
Texas Instruments TPS7A9001DSKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A9001DSKR — Power Management & Signal Chain | Superb Automation

TPS7A9001DSKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A9001DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A9001DSKR: 500 mA of low noise in a 2.5 mm square body

The TPS7A9001DSKR is a 500 mA adjustable regulator in a ten pin WSON body measuring 2.5 mm by 2.5 mm, with 4.7 uV RMS of noise over 10 Hz to 100 kHz and 100 mV of maximum dropout at the full 0.5 A. The output is set by an external divider anywhere from 0.8 V to 5.7 V, the input accepts 1.4 V to 6.5 V, and the junction to case thermal resistance is 3.2 C per W, which is what makes half an amp survivable in that footprint.

The rejection curve is the reason the part exists: 60 dB at DC, 50 dB at 100 kHz and 30 dB at 1 MHz, with 1 percent accuracy over line, load and temperature. Small cells and remote radio units put a linear regulator next to a PLL or a VCO, where the switching supply upstream is a few centimetres away and the phase noise budget cannot absorb its ripple. A part with 30 dB of rejection at 1 MHz removes most of that without a second converter stage.

Key electrical data for the 500 mA part

Input range1.4 V to 6.5 V, with the output adjustable from 0.8 V to 5.7 V
Output current500 mA, with a foldback current limit and thermal shutdown
Dropout100 mV maximum at 0.5 A to a 5 V output, 200 mV to 5.7 V
Noise4.7 uV RMS from 10 Hz to 100 kHz, independent of the set point
Rejection60 dB at DC, 50 dB at 100 kHz and 30 dB at 1 MHz
Soft startselectable charging current, so the inrush into the output capacitor can be set
Accuracy1 percent over line, load and temperature, from a 0.8 V reference

Package, marking and reel data

BodyWSON DSK, 10 pins, 2.50 mm by 2.50 mm, thermal pad
Reel3000 pieces, large tape and reel, 8 mm tape on a 330 mm carrier
Finish and moistureNIPDAU, level 2, 260 C peak reflow, one year floor life
Marking1CEP
Small quantity optionDSKT carries 250 pieces on a small reel for prototypes

Where 500 mA at 4.7 uV belongs

Macro remote radio units, outdoor backhaul, massive MIMO antenna systems, ultrasound scanners, lab instruments and radar front ends all share a supply problem: several low voltage analog rails, each a few hundred milliamps, each feeding a device whose noise figure is specified in fractions of a decibel. A 2.5 mm regulator with a divider sets any of those rails, and the same order code covers 1.2 V, 2.5 V and 3.3 V, which keeps the approved list short. The 2.5 mm body also fits under a shield can, which is where a radio board usually wants its analog supply.

The thermal path is the only real constraint. At 500 mA from 3.3 V into 1.8 V the part burns 750 mW, and 3.2 C per W junction to case means the case has to be held near ambient by the pad and the copper. In a 2.5 mm body there is no room for a large lead frame, so the recommended land pattern with vias into a ground plane is the difference between a 40 C rise and a thermal shutdown at 60 C ambient. The same rule applies to the divider: two 1 percent resistors at the feedback node add their tolerance to the 1 percent of the part, so a 0.1 percent pair is worth the extra cent on a rail that is specified at 1 percent overall.

Buyer questions on the TPS7A9001DSKR

Is the output fixed at the factory? No, this code is adjustable. The output is set by two resistors from OUT to FB and FB to ground, and the 0.8 V reference with 1 percent accuracy sets the floor of the range.

How is the soft start current chosen? A capacitor on the soft start pin and the internal selectable charging current set the ramp. The slower ramp reduces inrush but delays the rail, which matters when a downstream device has a power-up sequence.

Does the part need a noise reduction capacitor? The noise figure is specified with the recommended external capacitor on the NR pin. Without it the regulator still regulates, but the low frequency noise rises above the 4.7 uV figure.

Buying this regulator through a component supplier

A 2.5 mm regulator that feeds a VCO is usually one of a dozen lines on a radio board, and the sourcing question is availability rather than choice. Our RF component sourcing page covers the analog and RF supply lines that sit beside this part. When a customer needs to compare bodies, power management cross reference has the pin out and the thermal pad geometry side by side.