Contact Us

ADL5385ACPZ-R7

Brand: Analog Devices
Analog Devices ADL5385ACPZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADL5385ACPZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADL5385ACPZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADL5385ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADL5385 quadrature modulator: 30 MHz to 2200 MHz with the local oscillator at twice the carrier

The ADL5385 is a silicon quadrature modulator that covers 30 MHz to 2200 MHz, takes a single ended local oscillator at twice the output frequency, and delivers 11 dBm of output compression point at 350 MHz with 50 dBc of sideband suppression and 46 dBm below the carrier of feedthrough at the same frequency. It runs from a single 4.75 V to 5.5 V supply in a 24-lead LFCSP with an exposed pad, and it drives a 50 ohm load single ended from a differential output stage.

Published values

ParameterValue
Output frequency range30 MHz to 2200 MHz
Output compression point11 dBm at 350 MHz
Sideband suppression50 dBc at 350 MHz
Carrier feedthrough46 dBm below the carrier at 350 MHz
Local oscillator inputsingle ended, at twice the output frequency, divided by two inside the part
Baseband inputsdifferential, wide bandwidth, usable as baseband or as a complex intermediate frequency
Supply4.75 V to 5.5 V single supply
Output load50 ohm, driven from a differential to single ended stage
Package24-lead LFCSP with exposed pad
Application fitradio link transmitters, cable modem termination systems, UHF and VHF radio, broadband wireless access

The local oscillator has to be at twice the carrier

The internal quadrature is generated by a divide by two stage, so a 900 MHz output needs a 1800 MHz local oscillator. That is convenient because a divider gives an accurate 50 percent duty cycle and a clean quadrature relationship whatever the input duty cycle is, and it is inconvenient because the oscillator has to reach twice the highest output frequency, which at the top of the band is 4.4 GHz.

The divider also means the local oscillator leakage at the output sits at the output frequency, not at the oscillator frequency, and the level of that leakage depends on the balance of the divider and the output stage rather than on the oscillator drive level. An oscillator that is too strong can push the divider into a state where the duty cycle degrades, which shows up as a rise in carrier leakage and a fall in sideband suppression.

What the 46 dBm feedthrough figure really says

A carrier feedthrough of 46 dBm below the carrier, with an 11 dBm output, is 57 dB of suppression. That number is set by the DC offset at the baseband inputs, because any DC at those pins multiplies with the local oscillator and appears at the carrier frequency. The part has internal bias that sets a nominal zero, but the source driving the baseband inputs also has an offset, and that offset is what the 57 dB is measured against.

In a direct conversion transmitter the same mechanism is what produces local oscillator leakage at the antenna, and it is measured as an absolute power rather than as a ratio, because the leakage is independent of the wanted signal level. A system specification that quotes a maximum leakage in dBm at the antenna therefore limits the baseband offset and the gain of the chain after the modulator.

Sideband suppression depends on the drive, not only on the part

50 dBc of sideband suppression at 350 MHz is a measurement made with a well matched differential drive. The suppression is limited by the amplitude and phase balance between the in phase and quadrature paths, so any imbalance in the source adds to the imbalance inside the part. A driver that delivers 0.1 dB of amplitude difference and one degree of phase difference between the two paths will degrade the figure the part can reach.

At higher output frequencies the same balance has to hold over a wider bandwidth, which is why the data sheet quotes the number at 350 MHz and gives curves elsewhere. A transmitter that has to meet a spectral mask at 2 GHz should be evaluated at 2 GHz with the actual baseband filter, not inferred from the low frequency figure.

Buyers usually arrive at vendor consolidation to find the family alternatives, then use the amplifier cross reference to confirm a substitute before it is fitted; the ADI second source page is the routine for a part that has already stopped shipping.

Two questions buyers ask

Can the ADL5385 be used as an upconverter with a complex intermediate frequency? Yes. The baseband inputs have enough bandwidth to accept a complex intermediate frequency, and the part then translates it to the final frequency in one step. The limit is the flatness of the baseband path, not the modulator itself.

Does the exposed pad have to be soldered? Yes. The pad is the thermal and electrical reference for the output stage, so a package placed without it will run hot and lose performance. It is also the ground return for the modulator.