ADG1434YCPZ-REEL7
Product Specifications
ADG1434YCPZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1434YCPZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1434YCPZ-REEL7: four SPDT switches at 4 ohm in a 4 mm LFCSP
The ADG1434YCPZ-REEL7 is a quad single-pole double-throw analog switch built on the iCMOS process, in the 4 mm by 4 mm LFCSP on tape and reel. It is fully specified at plus or minus 15 V, at plus 12 V single supply and at plus or minus 5 V, offers 4.7 ohm maximum on resistance at 25 C with 0.5 ohm of flatness, and carries up to 115 mA per channel. The four channels switch independently, each with break-before-make action so a channel never shorts its two inputs together during the transition.
Published values
| Parameter | Value |
|---|---|
| Configuration | Four independent SPDT switches |
| Supply options | Plus or minus 15 V, plus 12 V single, plus or minus 5 V, all specified |
| On resistance | 4.7 ohm maximum at 25 C, dual supply |
| On resistance, 12 V single supply | 6 ohm typical at 25 C, 9.5 ohm maximum over minus 40 C to 125 C |
| On resistance match | 0.55 ohm typical, 0.85 ohm maximum over temperature |
| On resistance flatness | 0.5 ohm, 1.5 ohm typical and 2.5 ohm maximum at 12 V |
| Continuous current | Up to 115 mA per channel |
| Logic levels | 3 V logic compatible inputs |
| Switching action | Break before make |
| Enable pin | Fitted on the ADG1434 in the LFCSP body only |
| Package | 20-lead 4 mm by 4 mm LFCSP, also 20-lead TSSOP in other codes |
Two supply ranges, two resistance curves
The headline 4.7 ohm maximum belongs to the plus or minus 15 V condition. On a plus 12 V single supply the typical on resistance at 25 C is 6 ohm and the guaranteed maximum over minus 40 C to 125 C is 9.5 ohm, with channel to channel match at 0.82 ohm over the same window and flatness of 2.5 ohm. A program that budgets 4.7 ohm from the first page and then runs the part from 12 V single supply has understated the resistance by half at hot and cold extremes. For a switch driving an ADC input or a gain setting resistor, the flatness figure matters more than the absolute value, because flatness shows up as distortion while absolute resistance only shows up as gain error that can be calibrated out.
Break before make and what it protects
Each channel opens its current path before it closes the new one, so the two throw inputs are never connected together, not even for the few nanoseconds of a transition. In a multiplexer feeding an instrumentation amplifier this prevents the amplifier from seeing the difference between two source voltages through a low resistance path, which would otherwise produce a large transient at every channel change. It also matters when one throw is driven and the other is a low impedance source: without break before make, the switch would momentarily short the two sources. The delay is specified separately in the timing table, and a system that needs a shorter dead time than that value cannot use this part.
Why the enable pin is package specific
The enable input appears on the ADG1433 in both the LFCSP and the TSSOP, and on the ADG1434 only in the LFCSP. That difference is easy to miss when a file is moved between the two bodies, and it changes the pin count and the pinout. Disabling the part turns all channels off, which is the state a fault handler wants without having to drive four logic lines. A buyer comparing the ADG1434 in LFCSP with the same function in TSSOP is not comparing two packages of one part; the TSSOP version of the quad does not carry the enable pin at all.
Where a 4 ohm switch earns its price
At 115 mA per channel the switch dissipates about 53 mW, which is a small number that becomes significant in a 4 mm package with sixteen channels in a rack. The iCMOS process is what allows 33 V operation with a resistance this low, and the low flatness is why the part is used in data acquisition and gain switching rather than in power routing. For anything above 115 mA per channel the answer is a relay or a discrete pair, not this part. The comparison work sits on the ADI part second source page, the substitution question is covered on pin to pin cross reference, and consolidating the switch and converter lines under one supplier is described on one stop BOM sourcing.