Contact Us

TPS66121YBGR

Brand: Texas Instruments
Texas Instruments TPS66121YBGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS66121YBGR — Power Management & Signal Chain | Superb Automation

TPS66121YBGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS66121YBGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS66121YBGR USB Type-C sink path with a 5 V VBUS regulator

The TPS66121YBGR is the 5 V member of the TPS6612x family, an integrated sink power path for a USB Type-C port that also carries a linear regulator fed from VBUS. The path is one N channel FET of 22 milliohm typical that stands 32 V, so a charger that negotiates badly or a cable that carries a surge does not take the part out. In normal use the path conducts from 4 V to 22 V at up to 5 A, which covers plain 5 V charging through to the 20 V contracts of a notebook port. The body is a 28 ball WCSP of 1.606 mm by 2.806 mm, and the vendor states that no high density interconnect is needed to fan it out, which keeps a two layer section viable where the port sits close to the connector.

The regulator on this device holds VBUS at 5.0 V. The TPS66120 in the same family holds it at 3.3 V, and that is the only functional difference between the two order codes, so a board that runs a 3.3 V housekeeping rail has to buy the TPS66120 and a board that wants 5 V for its system load has to buy the TPS66121.

Protection sits on both sides of the path. Overvoltage on VBUS is set by an external resistor divider on the OVP pin and is disabled by grounding that pin, which matters when the port is fed from a fixed adapter and the divider would only add leakage. Undervoltage is monitored on the system supply and on VBUS. Reverse current is blocked, so a system rail that still holds charge does not feed back down the cable when the charger is pulled. A fault pin reports overtemperature with a de-glitch, and the path has a soft start that limits the inrush into the load capacitance at plug in.

Key parameters from the SLVSEW9B document

FunctionUSB Type-C sink power path with an integrated VBUS regulator
Sink FET22 milliohm typical, 32 V tolerant N channel device
Sink range4 V to 22 V, up to 5 A
Regulator output5.0 V on the TPS66121, 3.3 V on the TPS66120
OvervoltageThreshold set by an external divider on OVP, disabled when OVP is grounded
UndervoltageMonitored on the system supply and on VBUS
Reverse currentBlocked, so the system rail cannot discharge into the cable
Fault reportingFLT pin, de-glitched against a short overtemperature event
Start-upBuilt-in soft start limits the inrush into the load capacitance
PackageYBG 28 ball WCSP, 1.606 mm by 2.806 mm, moisture level 1
Order codeTPS66121YBGR, large reel, active in the vendor addendum

What separates the two devices in this family

The TPS66120 and the TPS66121 share the die, the pinout and the ball map. The regulator target is the difference, 3.3 V against 5 V, and it is fixed at the factory rather than set by a resistor. A buyer who orders by family name can therefore receive a part that regulates to the wrong rail, and the board will still power up, which is the worst kind of error because it passes a smoke test and fails in the field. The ball map does not make the difference visible, and the marking on a 28 ball WCSP is small enough that a receipt check has to read the reel label rather than the part.

Where a product needs both rails, the usual arrangement is the sink path for the port and a separate small regulator for the housekeeping rail, because the integrated regulator on this device is not a second output. The vendor document shows the regulator supplying the device itself and other system components during a dead battery condition, which is the case where the port is connected but the main battery is flat.

Where this part fits

Notebook and desktop main boards, Chromebook and Windows on ARM platforms, docking stations, port adapters and cable dongles. All of those have a Type-C port that has to survive a user plugging in the wrong charger, and all of them want the port path and its protection in one body rather than a discrete FET plus a comparator chain. Our sourcing desk keeps the family substitution notes for these port parts under power management cross reference, and the receipt checks that catch a wrong rail at the dock are in incoming inspection plan.

What to check before a purchase order

Check the divider on OVP against the highest VBUS the charger can present, not against the 5 V contract. A 20 V contract with a 5 percent tolerance and a transient on cable removal reaches the top of the divider window, and the divider has to trip below the 32 V rating of the FET with margin for the tolerance of both resistors. A divider copied from a 5 V only product will let a 20 V adapter through to the system.

Check the thermal path under the balls. The 22 milliohm FET dissipates about 0.55 W at 5 A, which is small in absolute terms but sits in a 4.5 square millimetre body with no exposed pad. The vendor's routing guidance for the ball field is what keeps the junction below the overtemperature trip, and a board that pours no copper into the ball field will hit that trip at a lower current than the 5 A rating suggests. Power path parts of this class are also worth holding to a date code check, because the pass FET is the part that fails first in a field return.

Questions that come up on this part

Can the regulator be used with the port unplugged? The regulator is fed from VBUS, so with no cable there is no input and no output. The dead battery case the document describes is a port that is plugged in while the battery is flat, which is still a live VBUS.

What happens if the OVP pin is left floating? The document specifies the pin as a divider input and gives the disable condition as a ground connection. A floating pin is not one of the two defined states, so the divider belongs on the board even when the threshold is set high.