Contact Us

TPS65563ARGTR

Brand: Texas Instruments
Texas Instruments TPS65563ARGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65563ARGTR — Power Management & Signal Chain | Superb Automation

TPS65563ARGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65563ARGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65563ARGTR photo flash charger with an integrated IGBT driver

The TPS65563ARGTR is a charger for a photo flash capacitor with an insulated gate bipolar transistor driver on the same die. It runs from a battery input of 1.4 V to 12 V and a control supply of 2.7 V to 5.5 V, integrates a 50 V power switch with a lower on resistance than the earlier member, and detects charge completion on the primary side rather than across the flash tube. The body is a 16 pin QFN of 3 mm by 3 mm, which is small enough to sit beside the capacitor it charges.

The charging current is set by a resistor that programs the peak primary current anywhere from 0.5 A to 2 A, and the pulse width modulation scheme adapts the switching pattern as the capacitor voltage rises, so the charge time stays short without exceeding the input current budget of a battery. A comparator detects the peak current, a second comparator detects switch turn on, and a third detects charge complete, which is why the part needs very few external components around it.

The IGBT driver is what makes this a system block rather than a charger. It turns the flash tube on and off with a controlled gate waveform, and the logic outputs tell the host when the capacitor is ready and when the flash can be fired.

Key parameters from the SLVS858A document

Battery input1.4 V to 12 V on VBAT
Control supply2.7 V to 5.5 V on VCC
Power switchIntegrated 50 V device with a lower on resistance than the previous member
Peak currentProgrammable from 0.5 A to 2 A on the primary side
Charge detectionPrimary side charge complete detection with high accuracy
Flash controlIntegrated IGBT driver, with charge enable, flash acceptable and flash on signals
Charging behaviourOptimised switch on and off control for short charge time and high efficiency
PackageRGT 16 pin QFN of 3 mm by 3 mm, 3000 pieces on a large reel
Moisture levelLevel 2 with a one year floor life
Ambient rangeMinus 35 to 85 degrees on the published rows

The minus 35 degree floor is worth noticing

Almost every part on this site starts at minus 40 degrees. This one is published from minus 35 to 85 degrees, which is a five degree difference that matters for a camera sold into a cold climate specification. A product with a minus 40 degree requirement needs a different charger or a documented deviation, and the requirement is usually written in the product specification long before anyone looks at the charger data sheet.

The second unusual item is the split supply. The 1.4 V battery input and the 2.7 V control input are separate pins, so a product that runs its logic from 3.3 V and its flash from a single cell can use the part without an extra regulator, but a product that has only the battery has to generate the control rail first.

Where this part fits

Digital still cameras, camera phones with a xenon tube, industrial cameras with a flash head and any product that charges a photo flash capacitor from a battery. The sourcing notes for this class sit under power management cross reference and obsolete part cross reference hub.

What to check before a purchase order

Check the ambient rating against the product specification first, because this is the one parameter that cannot be fixed on the board. Then check the peak current setting against the battery, since a 2 A peak from a single cell at low state of charge pulls the rail down and the charger has to be set for the internal resistance of the cell rather than for the fastest charge time.

Check the capacitor voltage rating as well. The switch is rated 50 V and the capacitor charge target has to sit below that with margin for the detection tolerance. The incoming check for the reel is in incoming inspection plan.

Questions that come up on this part

Does the part need an external diode? The boost path uses the integrated switch and an external diode and capacitor, and the diode has to be a fast recovery type rated above the capacitor voltage.

Can two flash heads share one charger? Not without external switching, because the charge complete detection is written for one capacitor and one tube.

One more point about the charge cycle. The capacitor is charged in pulses whose width narrows as the voltage rises, so the input current stays roughly constant while the output power falls, which is what keeps a battery powered camera from browning out during a flash charge. The charge complete comparator works on the primary side, which removes the divider string that a secondary side sense would need and with it the leakage path across the capacitor.