TPS72218DBVR
Product Specifications
TPS72218DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS72218DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS72218DBVR 1.8 V regulator that needs no output capacitor
The TPS72218DBVR is a 50 mA linear regulator in a five pin SOT-23 that works from an input as low as 1.8 V and is stable with an output capacitor of 0.1 microfarad or even with none at all. That combination is aimed at two cell products, where the input falls towards 2 V and the board has no room for the 1 microfarad or 2.2 microfarad capacitor that most regulators need. Dropout is 50 mV at 50 mA, quiescent current is 85 microamps, and shutdown current is 1 microamp.
The family covers 1.5 V, 1.6 V and 1.8 V fixed outputs plus an adjustable member, all in the same body. The low input requirement is the headline: a regulator that needs 2.5 V to start cannot be fed from two AAA cells that have run down, and this part keeps regulating until the input reaches its own dropout floor.
The part is old enough that its document is written in the short form of the period, and the electrical table carries the numbers a modern reader still needs: 1.8 V to 5.5 V input, 50 mA continuous output, 50 mV of dropout at full load, and a quiescent current of 85 microamps rising to 120 microamps at the top of the temperature range.
Key parameters from the SLVS390B document
| Input range | 1.8 V to 5.5 V |
| Output | 1.8 V fixed on this order code, with 1.5 V and 1.6 V siblings |
| Output current | 50 mA continuous |
| Dropout | 50 mV typical at 50 mA |
| Quiescent current | 85 microamps typical, 120 microamps at the high end of the range |
| Shutdown current | 1 microamp |
| Output capacitor | Stable with 0.1 microfarad, capacitor free operation supported |
| Package | DBV five pin SOT-23 |
| Order code | TPS72218DBVR, large reel, active in the vendor addendum |
What capacitor free operation really means
A regulator that is stable without an output capacitor is useful in two cases: a board where the load is a few millimetres from the pin and the load's own input capacitance is enough, and a board where the output capacitor would have to be a tantalum because of a legacy bill of materials. Removing the capacitor also removes a component that can fail short and take the rail down, which is a reliability argument rather than an electrical one.
The cost is transient response. Without an output capacitor the load step is absorbed by the regulator loop alone, so a 20 mA step produces a larger deviation than the same step with 1 microfarad in place. On a sensor or a small radio the deviation is tolerable; on a load with a fast current edge it is not, and the capacitor comes back.
Where this part fits
Portable communication devices, battery powered instruments, two cell products and legacy boards that are being cost reduced rather than rebuilt. The 1.8 V input floor is what makes it usable from two alkaline cells or from a single lithium cell through most of its discharge. Notes on replacing an older regulator without adding a capacitor are under power management cross reference, and the checks for a long life part on receipt are in incoming inspection plan.
What to check before a purchase order
Check the load step against the capacitor choice. The document supports operation without an output capacitor, but a load that switches tens of milliamps in a microsecond needs the capacitor, and the value that works is the one that keeps the deviation inside the load's window rather than the smallest value the part tolerates.
Check the quiescent current against the standby budget. At 85 microamps this part is two orders of magnitude above the 1 microamp family, so it belongs on a rail that is switched off in sleep rather than on the always-on rail. A product that leaves it enabled through a long standby will find that the regulator, not the load, is the drain.
Check the dropout at the real load. Fifty millivolts at 50 mA leaves a 1.8 V rail in regulation down to a 1.85 V input, which is inside the range of two fresh alkaline cells and outside it for a pair that has run down. A product that quotes operation to 2.0 V has to accept that the rail follows the input below 1.85 V.
Questions that come up on this part
Is 0.1 microfarad a minimum or a typical value? It is the value the part is specified to be stable with, so it is a minimum in practice, and zero is allowed where the load provides the capacitance.
Can it deliver more than 50 mA in a pulse? The document gives 50 mA continuous and does not publish a higher peak, so a load with a large inrush needs a different part.