TPS7A2028PDBVR
Product Specifications
TPS7A2028PDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A2028PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A2028PDBVR: a 300 mA low noise regulator with active discharge that holds 2.8 V from a 1.6 V to 6 V input in a five pin SOT-23
TPS7A2028PDBVR is an ultra low noise linear regulator with 7 microvolt RMS of output noise without a bypass capacitor, 95 dB of rejection at 1 kHz and a 6.5 microamp quiescent current in a SOT-23 (DBV) body of 5 pins. It holds a fixed 2.8 V with 1.5 per cent accuracy, drops 140 mV at 300 mA, works with 1 microfarad of ceramic on the output, limits inrush with an internal soft start, and pulls the output down through 150 ohm when the enable pin goes low. The junction range is minus 40 C to 125 C and the body is 2.90 mm by 2.80 mm.
Order code and package
| TPS7A2028PDBVR | SOT-23 (DBV) body, 5 pins, 2.90 mm by 2.80 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C with unlimited floor life, marking JH, active status in the addendum dated 25 October 2026 |
| TPS7A2028PDQNR | the same die in the X2SON (DQN) body, 4 pins, 1.00 mm by 1.00 mm, 3000 pieces on a large reel, marking 2AWF, which is the body for a board that has no room for the SOT-23 |
| TPS7A2028PYCKR | the DSBGA (YCK) body at 0.616 mm by 0.616 mm, 12000 pieces on a large reel, marking E, the smallest option in the family |
| TPS7A2028DQNR | the same body as the DQNR row without the P in the string, which is the version without active output discharge |
| P in the string | the letter marks the active discharge option, so a board that needs the rail pulled to zero on disable has to order the P string and cannot rely on the plain one |
| Other voltages | TPS7A2029 and the rest of the family carry the same die with a different internal setting, and the two digits after TPS7A20 select the output voltage |
| Marking | JH on the SOT-23, 2AWF on the X2SON and E on the DSBGA, which is the only way to tell the bodies apart on a mixed reel |
Electrical parameters that decide the application
| Input voltage | 1.6 V to 6.0 V, which covers a 1.8 V rail with 200 mV of headroom and a 5 V rail with a full volt of margin |
| Output voltage | 0.8 V to 5.5 V across the family, fixed inside the package per string, and 2.8 V on this one with no divider needed |
| Output current | 300 mA continuous, limited by the internal protection rather than by the five pin body |
| Accuracy | 1.5 per cent maximum over load, line and temperature, which is what the trimmed reference buys |
| Noise | 7 microvolt RMS from 10 Hz to 100 kHz at 300 mA, measured without a bypass capacitor on the output |
| Supply rejection | 95 dB at 1 kHz and 45 dB at 1 MHz, so the rejection holds up where a switching regulator ripple sits rather than only at audio frequencies |
| Quiescent current | 6.5 microamp typical, which is the number that decides whether the rail can stay on in a battery product |
| Dropout | 140 mV maximum at 300 mA with a 3.3 V output, and 145 mV on the DBV body, so a 2.8 V rail needs at least 2.94 V at the input for full current |
| Stability | stable with 1 microfarad of ceramic at the output, and the internal compensation is written for that value |
| Soft start | an internal ramp that limits the inrush at turn on, so a large output capacitor does not pull the input rail down |
| Enable | a smart enable input with a 500 kilohm pulldown that holds the regulator off when the pin floats, and the pulldown disconnects once the pin is driven high to save current |
| Active discharge | 150 ohm typical from the output to ground on the P strings, activated by the enable pin going low or by the input falling below the undervoltage threshold |
| Protection | thermal shutdown at 165 C and an undervoltage lockout that releases the part only when the input is high enough for the set output |
| Temperature | minus 40 C to 125 C junction, which is where the noise and rejection curves are drawn |
Family variants and how they differ
| With and without P | the P string pulls the output down through 150 ohm on disable, while the plain string leaves the output to decay through the load, which matters on a rail that feeds a converter or a reference |
| Four bodies | SOT-23 at 2.90 mm by 2.80 mm, X2SON at 1.00 mm by 1.00 mm and two DSBGA outlines at 0.616 mm, all the same die and the same electrical tables |
| Fixed output | the voltage is set inside the package, so there is no feedback pin and no divider, which removes two resistors and a noise injection path from the board |
| Reel size | 3000 pieces for the SOT-23 and the X2SON, 12000 for the DSBGA, which changes the minimum order for a small build |
| Family range | the same document covers 0.8 V to 5.5 V in fixed steps, so a rail change is a string change rather than a board change |
| Marking | the marking differs by body, and the two character codes on the DSBGA are the only identification after the reel label is gone |
Points to check before this part goes on a BOM
The 7 microvolt RMS figure is quoted without a bypass capacitor, which is the difference between this part and the older low noise regulators that need a dedicated noise reduction pin and a capacitor on it. That saves a pin, a part and a placement.
The 140 mV dropout at 300 mA sets the minimum input. A 2.8 V rail from a 3.0 V input has 200 mV of headroom at full load, which is inside the specification but leaves nothing for a sagging supply, so the input rail has to be checked at its lowest point rather than at nominal.
The P string matters when the rail has to be defined. A discharged rail that decays through the load leaves a converter or a reference in an unknown state for milliseconds, and the 150 ohm discharge removes that window.
The enable pulldown is 500 kilohm and it disconnects when the pin is driven high. That is why the input current stays at 6.5 microamp rather than climbing with the enable voltage, and why a board does not need an external pulldown resistor.
The DSBGA body is 0.616 mm square. It needs a 0.4 mm or finer stencil aperture, an inspected placement and a reflow profile written for the package, so the SOT-23 remains the practical choice unless the board area is the constraint.
Where 7 microvolts of noise is the deciding number
A phase locked loop, a voltage controlled oscillator, a camera sensor analogue rail and a data converter reference all convert supply noise into phase noise, jitter or code error. A switching regulator in front of those loads leaves ripple at the switching frequency and its harmonics, and a linear regulator with 95 dB of rejection at 1 kHz and 45 dB at 1 MHz removes most of it.
The alternative is a larger output capacitor and a ferrite bead, which costs board area and adds a resonance. At 300 mA and 6.5 microamp of quiescent current the regulator costs less area than the filter it replaces, which is why it appears on boards that already have a switcher upstream.
Where this order code fits
The part suits a camera sensor analogue rail, a phase locked loop supply, a medical sensor front end or a smart meter, where 300 mA is enough and the noise floor is the constraint. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Can it run from a 1.8 V rail? Yes, the input range starts at 1.6 V, but the output has to be low enough to leave the dropout. A 2.8 V output from a 1.8 V input is not possible; the 1.6 V figure is the input floor, not a headroom allowance.
Why is there no bypass capacitor pin? The noise is reduced inside the package, so the 7 microvolt RMS figure applies with only the 1 microfarad output capacitor. That is the reason the family fits a four pin package.
What does the P in the string do? It enables the active output discharge, a 150 ohm path from the output to ground that turns on when the enable pin goes low or the input collapses. A board that needs the rail at zero volts on disable orders the P string.
Is the X2SON body a drop in for the SOT-23? Not physically. The pin count and the land pattern are different, so the board has to be laid out for the body that is ordered. The electrical behaviour is the same across the four bodies in the family.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.