OP284ESZ-REEL7
Product Specifications
OP284ESZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The OP284ESZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
OP284ESZ-REEL7: 4 MHz, 65 uV and Rail to Rail on a 36 V Total Supply
The OP284ESZ-REEL7 is the dual member of the OP184, OP284 and OP484 family in the 8-lead SOIC: a single supply amplifier with rail to rail inputs and outputs, 4 MHz of gain bandwidth, 4.0 V per microsecond of slew rate, 65 uV of offset voltage and 3.9 nV per root hertz of voltage noise. The family is guaranteed from 3 V to 36 V total, which is plus or minus 1.5 V to plus or minus 18 V, it is unity gain stable, and it is specified over minus 40 to 125 C. The single is the OP184, the dual is this part and the quad is the OP484, and the family carries military and enhanced product data sheets alongside the industrial one.
The reason this part exists in the catalogue next to a hundred other rail to rail amplifiers is the supply ceiling. Most rail to rail input amplifiers stop at 5.5 V total, and a 24 V industrial front end cannot use them without a pre regulator. This one runs at 36 V and still accepts inputs at both rails.
Four megahertz at a gain of 100 is 40 kHz, and that is the number that matters
Gain bandwidth is quoted at unity gain and falls as a single pole above it. At a gain of 100 the small signal bandwidth is 40 kHz, and the full power bandwidth at a 2 V peak to peak output is 637 kHz, so a stage that has to deliver 10 V peak to peak at 100 kHz is outside the part even at low gain. The two numbers are usually confused: 4 MHz is the frequency at which the open loop gain reaches one, and a 100 kHz signal at 10 V peak to peak needs a slew rate of 6.3 V per microsecond, which is above the 4.0 V per microsecond the part provides.
The 65 uV offset is 0.43 of a 16-bit bit on a 10 V span and 0.85 of a bit on 5 V. The noise over a 100 kHz band is 1.23 uV rms, which is 0.01 of a bit at 16 bits on 10 V, so the offset and not the noise is the accuracy term at that resolution. At 24 bits neither number is good enough on its own and the stage would have to be auto-zeroed or trimmed.
| Supply range | 3 V to 36 V total, plus or minus 1.5 V to plus or minus 18 V |
| Input and output | Rail to rail on both, unity gain stable |
| Bandwidth | 4 MHz at unity gain, 40 kHz at a gain of 100 |
| Slew rate | 4.0 V per microsecond, 637 kHz full power at 2 V peak to peak |
| Offset | 65 uV, 0.43 LSB at 16 bits on 10 V, 0.85 LSB on 5 V |
| Noise | 3.9 nV per root hertz, 1.23 uV rms over 100 kHz |
| Headroom | 50 percent above a 24 V rail before the 36 V ceiling |
| Temperature | Minus 40 to 125 C, industrial and enhanced versions in the same family |
| Package | 8-lead SOIC, also 8-lead PDIP for the same part number family |
A 24 V rail is 12 V below the ceiling, and the input window is why that matters
A 24 V industrial rail at plus 10 percent is 26.4 V, which leaves 9.6 V of headroom against the 36 V absolute maximum and is comfortable even with a load dump. The rail to rail input is what makes the part useful there: a 4 to 20 mA loop receiver with a 250 ohm sense resistor develops 1 V to 5 V, which is well inside the window, and a high side current sense that sits at the top rail needs an input that reaches it. A 5.5 V rail to rail part cannot do either at 24 V, and a 36 V part without rail to rail input cannot do the second.
The price of the wide supply is speed: 4 MHz is modest, and the same 65 uV offset in a 5 V part usually comes with 10 MHz or more. That trade is worth it when the signal is slow and the environment is not, which is the typical case for transducer conditioning in industrial equipment. Where the signal is fast, a two stage arrangement with a low voltage high speed amplifier behind a resistive divider is the usual answer, and the divider ratio sets the noise penalty.
Two questions buyers ask
Does the rail to rail input hold over the whole supply range?
The input stage is specified rail to rail over the 3 V to 36 V range in the family data sheet, and that is unusual: many parts with a rail to rail input have a second input pair that takes over near the positive rail and brings an offset step with it. The crossover behaviour is worth checking in the data sheet for the grade being bought, because the enhanced and military versions have their own tables and their own limits.
Can it drive a 16-bit converter directly?
At 65 uV of offset and 1.23 uV of noise over 100 kHz it can, provided the converter is not sampling faster than the amplifier can settle. The settling to 0.1 percent for a single pole at 4 MHz is about 0.3 us, which is 7 time constants, so a 250 kSPS converter with a 4 us window is served and a 1 MSPS converter is not. Above that rate the amplifier has to be faster and the offset budget has to be re examined.
Ordering and supply
The ESZ suffix is the 8-lead SOIC, lead free, in tape and reel. Substitution traps are the supply ceiling and the input topology: a part with the same 65 uV offset and 4 MHz but a 12 V maximum will fail on a 24 V rail, and a part with a 36 V rating but a conventional input pair will not accept a signal at the positive rail. Both differences are invisible in a one line distributor description.
We hold and source this family for production and repair. Start from the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and when a substitute has to be qualified in an existing instrument, the sequence in how to verify a drop in replacement puts the supply ceiling and the input crossover ahead of the socket check.
Request Quote — In Stock, 100% New & Original, Full Warranty