ADG1411YRUZ-REEL7
Product Specifications
ADG1411YRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1411YRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG1411YRUZ-REEL7: 1.5 Ohm Quad SPST, 190 mA per Channel, and the 2.6 Ohm Maximum
The ADG1411YRUZ-REEL7 contains four independently selectable single pole single throw switches on an iCMOS process, with 1.5 ohm typical on resistance, 2.6 ohm maximum over temperature, 0.3 ohm of on resistance flatness, 0.1 ohm of match between channels, continuous current of 190 mA per channel in the TSSOP and 250 mA in the LFCSP, and full specification at plus or minus 15 V, plus 12 V and plus or minus 5 V. It needs no separate logic supply, accepts 3 V logic with a 2.0 V high threshold, operates rail to rail, is AEC-Q100 qualified for automotive use, and comes in a 16-lead TSSOP or a 4 mm by 4 mm LFCSP. The digital control is inverted against the ADG1412: these switches close on a logic zero.
The family is the standard answer for replacing four small signal relays on a signal routing or gain switching board, and the number that decides whether that works is not the 1.5 ohm on the first page but the 2.6 ohm maximum at temperature.
Seventy three percent above the headline is the figure the board sees
From 1.5 ohm typical to 2.6 ohm maximum is 73 percent, and the maximum is what a production board has to live with. Into a 1 kOhm load, 1.5 ohm is 0.15 percent of gain error and 2.6 ohm is 0.26 percent, which is above the 0.1 percent resistors a precision stage is usually built from. Into 10 kOhm both figures are below 0.03 percent and the switch stops being the accuracy term. The 0.1 ohm match between channels is the number that matters for a differential path, because 0.01 percent of mismatch into 1 kOhm does not convert a differential signal into a common mode error.
The 0.3 ohm flatness is 20 percent of the typical on resistance, so the resistance changes by a fifth across the signal range. That variation, not the absolute value, produces distortion, and it is the reason a switch in series with a high impedance node is harmless while the same switch inside a resistive divider at a low impedance is not.
| Configuration | Four independent SPST switches, bidirectional |
| On resistance | 1.5 ohm typical, 2.6 ohm maximum over temperature |
| Flatness | 0.3 ohm, 20 percent of the typical on resistance |
| Match | 0.1 ohm between channels, 0.01 percent into 1 kOhm |
| Current | 190 mA continuous per channel in the TSSOP, 250 mA in the LFCSP |
| Drop at 190 mA | 494 mV and 94 mW per channel through 2.6 ohm |
| Supplies | Plus or minus 15 V, plus 12 V, plus or minus 5 V, all fully specified |
| Logic | 3 V compatible, 2.0 V high and 0.8 V low, no logic supply pin, closes on logic zero |
| Qualification | AEC-Q100 for automotive applications |
| Packages | 16-lead TSSOP and 16-lead 4 mm by 4 mm LFCSP |
One hundred and ninety milliamps costs 94 mW, and four channels cost 376 mW
At the rated current the switch drops 494 mV, which is fine for a signal path and not fine for a power path: 494 mV at 190 mA is 94 mW in one channel, and four channels at that load dissipate 376 mW inside a 16-lead TSSOP with no exposed pad in the TSSOP version. The LFCSP version carries 250 mA and has a thermal pad, which is the reason it exists. A board that intends to use this part to switch a load rather than a signal should be looking at the package thermal resistance before the current rating, and at 250 mA in the LFCSP the drop is 650 mV and the dissipation 162 mW per channel.
The iCMOS construction is what allows plus or minus 15 V operation in a 4 mm package. A plus or minus 10 V signal path has 5 V of headroom per rail in the plus or minus 15 V mode and sits exactly on the limit in the plus or minus 12 V mode, so a 10 percent rail tolerance has to be counted. Single supply operation to plus 12 V covers a 12 V industrial rail and leaves nothing for a transient, which is why the plus or minus 15 V mode is the usual choice when the signal itself reaches 10 V.
Two questions buyers ask
Can it replace a reed relay in a signal path?
Electrically yes, with the same two limits that apply to every CMOS switch: 2.6 ohm of on resistance is far above a reed contact, and when off the switch blocks to the supplies but presents a capacitance rather than an open circuit. Above a few megahertz the off capacitance sets the isolation and the relay comparison stops being useful.
Is the automotive qualified version the same part number?
No. The AEC-Q100 versions carry their own order codes and their own temperature and test tables, and the qualification is on the part number, not on the family. A commercial reel and a qualified reel look identical on the first page and are not interchangeable in a production approval, so the order code has to be checked against the customer's approved vendor list rather than against the data sheet family name.
Ordering and supply
The YRUZ suffix is the 16-lead TSSOP, lead free, in tape and reel. The traps in this family are the control logic, which is inverted against the ADG1412 and mixed on the ADG1413, the supply ceiling of plus or minus 15 V, and the package current rating. A reel of the wrong logic variant makes every switch behave backwards with no visible difference on the board, and a TSSOP used at the LFCSP current rating runs 60 mA above its rating with no external sign until the part fails.
We hold and source this family for production and for repair. Start at the analog mixed signal ICs family page, compare a candidate against the pin to pin cross reference, and where a switch has to change on a board that is already built, the order in how to verify a drop in replacement puts the control sense and the current rating ahead of the socket check.
Request Quote — In Stock, 100% New & Original, Full Warranty