AD8672ARZ-REEL7
Product Specifications
AD8672ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8672ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8672ARZ-REEL7: 2.8 nV of Noise, 75 uV of Offset and 10 MHz, in a Dual
The AD8672ARZ-REEL7 is a dual precision amplifier with 2.8 nV per root hertz of voltage noise, 77 nV peak to peak from 0.1 Hz to 10 Hz, 10 MHz of bandwidth, 12 nA maximum of input bias current, 75 uV maximum of offset voltage, 120 dB minimum of open loop gain, and 3 mA typical of supply current per amplifier. It runs from plus and minus 5 V to plus and minus 15 V, is unity gain stable, shows no phase reversal, and is stable with capacitive loads above 1000 pF. The part is specified from minus 40 C to 125 C; the AD8672-EP variant extends to minus 55 C with a controlled baseline, one assembly site and a DSCC drawing number for defence and aerospace work.
The combination of 2.8 nV and 75 uV in the same part is what makes it useful: a low noise amplifier with a millivolt of offset cannot be used in a DC instrument without trimming, and a precision amplifier with 20 nV of noise loses bits on a wideband signal. This part holds both at once, at 3 mA per amplifier on a plus and minus 15 V supply, which is 90 mW for the pair.
Two point eight nanovolts over 100 kHz is 885 nV, and 75 uV is half a bit at 16 bits
Two point eight nanovolts per root hertz integrated over 100 kHz is 885 nV RMS, which against a 16-bit converter on a 10 V span, where one bit is 152.6 uV, is 0.006 of a bit. The broadband noise is therefore irrelevant at 16 bits and only becomes the limit at 20 bits or more, or in a wideband application where the signal itself is small. The 77 nV peak to peak from 0.1 Hz to 10 Hz is the number that matters in a DC instrument, because that is the band where a slow measurement actually sits.
Seventy five microvolts of maximum offset on the same 10 V span is 0.49 of a 16-bit LSB, and the drift is low enough that it does not double over temperature the way a general purpose part does. That combination is what a precision DC channel needs: the offset is calibrated once and stays calibrated, and the noise floor is below a bit. For 18 bits the offset becomes 3.1 LSB and has to be trimmed per board, which is where the precision stops being free.
| Voltage noise | 2.8 nV per root hertz, 77 nV peak to peak from 0.1 Hz to 10 Hz |
| Bandwidth | 10 MHz, unity gain stable |
| Offset voltage | 75 uV maximum, 0.49 LSB of a 16-bit converter on 10 V |
| Input bias current | 12 nA maximum, 12 uV into 1 MOhm |
| Open loop gain | 120 dB minimum |
| Supply current | 3 mA per amplifier typical, 90 mW for the pair on 30 V |
| Supply range | Plus and minus 5 V to plus and minus 15 V |
| Load stability | Stable with more than 1000 pF, no phase reversal |
| Temperature | Minus 40 C to 125 C, the EP variant to minus 55 C |
| Package | 8-lead SOIC, also 8-lead MSOP |
Twelve nanoamps into a megohm is 12 uV, a sixth of the offset
The 12 nA of bias current is not a JFET number and it is not a problem at moderate impedances: into 1 MOhm it produces 12 uV, which is 16 percent of the 75 uV offset. At 10 MOhm it produces 120 uV, larger than the offset, and the part stops being a precision amplifier in that circuit. The crossover is at 75 uV divided by 12 nA, or 6.25 MOhm, above which the bias current dominates. That is high enough for most filter and instrumentation work and low enough that a photodiode or pH electrode needs a different input stage.
The 1000 pF load stability is unusually generous for a 10 MHz part and it comes from the internal compensation. It matters when the amplifier drives a cable or a long trace, and it matters in a filter where the feedback network presents capacitance at the inverting input. A part with 10 MHz and 50 pF of load stability needs a series resistor in those positions, which changes the filter response.
Two questions buyers ask
What is the difference between the standard part and the EP variant?
The EP variant is specified from minus 55 C to 125 C, has a controlled baseline with one assembly and test site and one fabrication site, and carries a DSCC drawing number. It is the same amplifier for defence and aerospace procurement, where the documentation and the single-site baseline are the requirement rather than the electrical performance. A commercial board does not need it, and a programme with a drawing number cannot use the standard part.
Is it a good PLL loop filter amplifier?
Yes, that is one of the named applications. The loop filter needs low noise at low frequency, low bias current into the integrator capacitor and enough bandwidth for the loop, and this part has all three. The bias current is the one to check against the resistor values in the filter, because a 12 nA bias into a 1 MOhm resistor is 12 uV of offset that the loop integrates.
Ordering and supply
The ARZ suffix is the 8-lead SOIC in tape and reel. Substitution traps are the bias current, the load stability and the noise at low frequency. A part with a bipolar input and 500 nA of bias fails at 1 MOhm, and a part with 2.8 nV of broadband noise and 100 nV at 10 Hz reads worse in a DC instrument even though the headline looks the same.
We hold and source this family for production and for repair lots. Start from the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and where a substitute has to be proven on an existing board, the order in how to verify a drop in replacement puts the bias current and the load stability first.
Request Quote — In Stock, 100% New & Original, Full Warranty