ADA4610-2ARZ-R7
Product Specifications
ADA4610-2ARZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4610-2ARZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADA4610-2ARZ-R7: 5 pA of Bias Current and the Drift That Beats the Offset
The ADA4610-2ARZ-R7 is a dual JFET input operational amplifier with rail to rail output, 5 pA of typical input bias current, 7.3 nV per root hertz voltage noise at 1 kHz, 0.45 uV peak to peak noise from 0.1 Hz to 10 Hz and 0.00025 percent total harmonic distortion plus noise. The A grade guarantees 1 mV maximum offset and 8 uV per degree C maximum drift in the SO-8, MSOP and LFCSP packages, the part runs from plus and minus 5 V to plus and minus 15 V, is unity gain stable, and does not exhibit output phase reversal when the inputs are driven beyond the common mode range. The order code carries the A grade, the SO-8 package and a tape and reel quantity.
Offset, drift and the grade that matters
One millivolt of offset is 13 least significant bits of a 16 bit converter on a 5 V span, which is a large number by precision standards, and the drift is what makes it worse: 8 uV per degree C over the 165 degree industrial range is 1.32 mV, which is 132 percent of the offset the part is bought for. The B grade halves both figures, at 0.4 mV and 2 uV per degree C, and the drift term then falls to 330 uV. The lesson is that the grade choice is decided by the temperature range of the product and not by the 25 C offset, and a product that needs a stable direct current offset over temperature should be reading the drift column first.
| Input bias current | 5 pA typical, 50 uV into 10 Mohm, 0.5 mV into 100 Mohm |
| Offset voltage, A grade | 1 mV maximum, B grade 0.4 mV |
| Offset drift, A grade | 8 uV per degree C, 1.32 mV over the full range |
| Offset drift, B grade | 2 uV per degree C, 330 uV over the full range |
| Voltage noise | 7.3 nV per root hertz at 1 kHz, 2.31 uV over 100 kHz |
| Low frequency noise | 0.45 uV peak to peak, 0.1 Hz to 10 Hz, 0.6 percent of a 16 bit LSB on 5 V |
| Distortion | 0.00025 percent total harmonic distortion plus noise, about minus 112 dB |
| Supply | Plus and minus 5 V to plus and minus 15 V, rail to rail output |
| Long term drift | 5 uV typical over 10,000 hours, 8 uV of temperature hysteresis |
| Stability | Unity gain stable, no phase reversal beyond the common mode range |
Where a JFET input actually pays
The 5 pA of bias current is the reason to buy this part, and the arithmetic says where it matters: into 10 Mohm it is 50 uV, into 100 Mohm it is 0.5 mV, and into 1 Gohm it is 5 mV. A bipolar input amplifier with 10 nA of bias current would produce 10 V into that last source, so the JFET input is not a refinement at high impedance, it is the only workable choice. Below about 1 Mohm the bias current error disappears and the offset and drift of the part become the limit, which is why a low impedance bridge does not need a JFET input at all.
The current noise is what pairs with the bias current. A JFET input has low current noise as well as low bias current, so the total noise into a high impedance source stays dominated by the source resistance rather than by the amplifier. At 1 Mohm and above, the thermal noise of the resistor is already several times the 7.3 nV of the amplifier, so the question moves to the resistor and to the bandwidth, not to the amplifier.
Phase reversal, capacitive load and the filter application
Phase reversal is a failure mode in which an amplifier whose input is driven beyond its common mode range drives its output to the opposite rail, and it turns a momentary overrange into a latch up that the feedback loop cannot recover. This family is specified not to do it, which is why it is used in front of a converter that can see an overrange at power up or during a fault. The rail to rail output and the stability into capacitive loads are what make it usable as a filter stage driving a converter's sampling capacitor.
The 0.00025 percent distortion is minus 112 dB, which is 2.5 ppm, and that is below the resolution of a 16 bit converter at full scale. The number to watch is not the distortion but the settling: a multi pole active filter built around this part has a settling time set by the filter, and the amplifier's own settling is a small term. That is the right order of priorities for an instrumentation filter, and it is why the part is common in medical and test equipment signal paths.
Two questions buyers ask
Is the A grade good enough, or is the B grade required?
It depends on the temperature range. At 25 C the 1 mV offset is the whole error and the A grade is fine; over 125 degrees the drift adds 1.32 mV, which is larger than the offset, and the B grade reduces that to 330 uV. A product that calibrates at production test and runs cool can use the A grade.
Can it drive a 16 bit converter directly?
Yes for the alternating current performance, since the noise and distortion are below a 16 bit least significant bit. For a direct current measurement the offset and drift are above one bit, so the converter's own offset calibration or a system level calibration is needed.
Ordering and supply
The ADA4610-2ARZ-R7 is the A grade, SO-8, tape and reel code of the dual. Cross references fail on the input stage, because a CMOS rail to rail part and a JFET part look similar on a specification table and behave differently on a high impedance source, and the bias current at temperature is where they separate. The grade also matters: an A grade reel and a B grade reel are the same silicon with different test limits.
We hold and source this family for production quantities and for repair lots. Start from the family page for analog mixed signal ICs, check a proposed alternative against the amplifier cross reference, and for patient connected or diagnostic equipment the qualification route in medical device components is the first checkpoint before a grade or a vendor changes.
Request Quote — In Stock, 100% New & Original, Full Warranty