TPS7A1601ADGNR
Product Specifications
TPS7A1601ADGNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A1601ADGNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A1601ADGNR: the adjustable 60 V member in the eight pin HVSSOP
The TPS7A1601ADGNR is the adjustable output of the TPS7A16 family, a 100 mA regulator that takes 3 V to 60 V at the input and sets its output from 1.2 V to 18.5 V through an external divider. Its quiescent current is 5 uA, its shutdown current is 1 uA, and it carries an open drain power good output with a delay that the user sets with a capacitor. The DGNR suffix is the eight pin HVSSOP body on a 2500 piece large reel.
The adjustable version is the one to choose when the rail is not a standard 3.3 V or 5 V. A 12 V or 24 V industrial bus, a 48 V telecom rail or a battery stack of several cells all fall inside the input window, and the divider can be set to whatever the downstream circuit needs. The reference is 1.193 V typical, with a window of 1.169 V to 1.217 V over temperature, so the divider ratio has to be calculated against the window rather than against the typical value alone.
Key electrical data for the adjustable member
| Input range | 3 V to 60 V, with the reference at 1.193 V typical and 1.169 V to 1.217 V over temperature |
| Output range | 1.2 V to 18.5 V set by an external divider, 100 mA maximum |
| Quiescent current | 5 uA typical, 15 uA maximum over the full temperature range |
| Shutdown current | 1 uA typical with the enable pin at 0.4 V |
| Dropout | 60 mV typical at 20 mA, 225 mV typical at 100 mA from a 4.5 V input to a 5 V output |
| Current limit | 265 mA typical, 500 mA maximum, with thermal shutdown at 170 C |
| Power good | 95 percent rising, 93 percent falling, 4 percent of hysteresis, delay set by a capacitor |
Package, marking and reel data
| Body | HVSSOP DGN, 8 pins, 3.0 mm by 5.0 mm, with a PowerPAD |
| Reel | 2500 pieces, large tape and reel, 330 mm carrier, 12 mm tape |
| Finish | NIPDAU, moisture level 2 with a one year floor life |
| Marking | PTYQ |
| Order code note | the vendor addendum prints TPS7A1601DGNR for this body, and the A suffix in this catalogue entry is not a published row |
Where a 60 V input linear regulator belongs
The obvious application is a low voltage rail derived from a high voltage bus: 24 V industrial control, 48 V telecom, a multi cell power tool pack, or the 12 V of a car audio and infotainment harness. The part is equally useful as a pre regulator in front of a switching stage, where it absorbs the surge and the load dump and leaves the converter with a bounded input. The 60 V rating is a continuous DC figure, and the data sheet is explicit that transients above it are handled by the pass element only within the energy the package can absorb.
The limit that catches engineers is dissipation. At 24 V in and a 5 V output at 100 mA the regulator dissipates 1.9 W, which no eight pin body can pass without a copper plane and, in most builds, an external heatsink. The data sheet notes that the maximum input voltage at full load is restricted to 24 V precisely because of this, and that higher inputs are usable only at lower current. A product that needs 100 mA at 48 V has to move to a switching topology.
Buyer questions on this adjustable code
Is the A suffix part of the published order code? The addendum for this document lists TPS7A1601DGNR, TPS7A1601DGNRG4, TPS7A1601DGNT and the SON equivalents, and it does not list an A row for this body. A purchase order should either name the published string or confirm the suffix with the vendor before the reel is committed.
How is the output set? With a divider from OUT to FB to ground. The reference is 1.193 V typical, so the upper resistor over the lower one equals the output over the reference minus one, and the divider should draw at least 10 uA so that the feedback current stays well above the leakage.
What sets the power good delay? A capacitor on the DELAY pin, charged by an internal current. With the pin open the delay is short and the trip point is 95 percent of the output rising and 93 percent falling.
Buying a high voltage regulator
High voltage linear parts are a small market, and second sources are rare, so an approved alternative list matters. The obsolete part replacement page describes how we verify a substitute on a high voltage rail, and last time buy and LTB planning covers the quantity decision when a vendor signals an end of life on a 2500 piece reel.
Two details decide whether the divider behaves. The feedback pin draws about 10 nA, so the divider should carry at least 10 uA to keep the ratio stable over temperature, and the reference window of 1.169 V to 1.217 V means a circuit that computes the ratio from the 1.193 V typical can land 2 percent away at the extremes. The power good output is open drain and asserts at 95 percent of the output rising and 93 percent falling, with a delay set by a capacitor on the DELAY pin, which allows a processor to see a clean flag rather than a chatter as the rail settles.