AD588TQ/883B
Product Specifications
AD588TQ/883B
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD588TQ/883B from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD588TQ/883B: 10 V, 1 mV of Initial Error and 1.5 ppm per Degree C
The AD588 is a multiple output precision voltage reference from Analog Devices built around a buried Zener cell with laser trimmed thin film resistors, and the TQ grade is the 16-lead ceramic DIP part specified over the full military temperature range. Initial error is 1 mV, drift is 1.5 ppm per degree C, and the pin programmed outputs are plus 10 V, plus 5 V, plus and minus 5 V tracking, minus 5 V and minus 10 V. Output noise is 6 microvolts peak to peak typical, force and sense terminals are brought out on each output for Kelvin connections, the ground sense is high impedance, and the optional fine trim does not change the operating point of the Zener or the buffer amplifiers, so it does not add drift.
The 883B suffix is a screening standard and not a temperature grade
The TQ identifies the ceramic package and the full military temperature range, and the 883B suffix identifies MIL-STD-883 screening. They are two separate requirements that happen to appear in one catalogue line, and a quote or a stock check has to carry both: a part that is military temperature but not screened is not the same purchase, and a part that is screened but has the industrial temperature grade is not either. In practice this is the single most common mismatch on this reference, and it is the reason a second source conversation about it has to start from the exact order code rather than from the part number alone.
One and a half ppm per degree C is 2.7 mV over the military range
Across a 180 C span from -55 C to +125 C, 1.5 ppm per degree C is 270 ppm, which on a 10 V output is 2.7 mV. A 12-bit converter with a 10 V full scale has a 2.44 mV LSB, so the drift over the whole military range is one LSB, and the 1 mV of initial error is another 0.41 LSB, so the total is about 1.5 LSB before anything else in the chain. That is what the data sheet means by 12-bit absolute accuracy: a 16-bit converter with a 10 V range has a 152 microvolt LSB and this reference does not hold it over temperature, though it does at a fixed 25 C after calibration.
Six microvolts of noise is not the limit, the drift is
Six microvolts peak to peak against a 152 microvolt LSB at 16 bits is 4 percent of a bit, so the reference's own noise is not what stops a 16-bit measurement. The drift is, and so is the initial error if the system does not calibrate. This is the split that decides how the reference is used: a system that calibrates against a known source at its operating temperature can use the 1 mV initial error and rely on the 1.5 ppm short term stability, while a system that never calibrates needs the initial error inside its budget from the first power-up. The Kelvin sense terminals are what let the reference be placed away from the load without the trace resistance appearing in the output.
| Parameter | Published value | What it decides |
|---|---|---|
| Initial error | 1 mV | 0.41 LSB at 12 bits on 10 V |
| Drift | 1.5 ppm per degree C | 2.7 mV over 180 C at 10 V |
| Outputs | 10 V, 5 V, plus and minus 5 V tracking, minus 5 V, minus 10 V | Pin programmed, no external parts |
| Tracking error | 1.35 mV at plus and minus 5 V over 180 C | The pair stays matched |
| Noise | 6 microvolts peak to peak typical | 4 percent of a 16-bit LSB |
| Sense terminals | Force and sense on each output | Kelvin connection at the load |
| Package | 16-lead ceramic DIP, TQ grade | Military temperature range |
| Screening | MIL-STD-883, 883B suffix | A separate requirement from the grade |
Can the tracking mode be used without external components?
Yes. The plus and minus 5 V tracking mode is set by the pin strapping and needs no external components, and the tracking error over the military range is 1.35 mV on the 5 V pair. The two outputs move together because they come from the same cell through trimmed amplifiers, which is what a bipolar converter needs for its positive and negative references. The fine trim pins are optional and are there for a system that wants to remove the last millivolt after its own calibration.
What is the practical difference between the ceramic and plastic versions?
The ceramic DIP versions cover the military range and the 883 screening, while the SOIC version is the industrial grade from -25 C to +85 C. The silicon is the same cell, so the room temperature accuracy is comparable, and the difference is the guaranteed window and the screening paperwork. For an instrument that ships with a calibration certificate the industrial part is usually enough; for a defence build the paperwork is the requirement. The converter and reference range is on the ADC and DAC cross reference, the checks for obsolete and screened parts are on the BOM shortage recovery page, and the complete index is the analog and mixed-signal index.
Request Quote — In Stock, 100% New & Original, Full Warranty