Contact Us

ADUM1200CRZ-RL7

Brand: Analog Devices
Analog Devices ADUM1200CRZ-RL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADUM1200CRZ-RL7 — Analog & Mixed-Signal ICs | Superb Automation

ADUM1200CRZ-RL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADUM1200CRZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADUM1200CRZ-RL7: two channels, one direction, and eight two milliamps at full rate

The ADuM1200 is a dual channel digital isolator with both channels pointing the same way, 2/0 directionality, built on transformer coupling rather than an LED and a photodiode. The order code reads C for the 25 Mbps grade, R for the narrow body 8-lead SOIC, Z for RoHS and RL7 for the reel. Each side can run from 2.7 V to 5.5 V independently, so the part also translates levels across the barrier, and it carries a refresh circuit that keeps the output correct when the input has not changed for a long time, which is the failure mode that makes an optocoupler with a low current transfer ratio drop a static logic level.

What the vendor page states

ParameterValue
Channelstwo, both in the same direction
Data ratedc to 25 Mbps NRZ, C grade
Supply2.7 V to 5.5 V on either side, level translation across the barrier
Current per channel, 5 V1.1 mA maximum up to 2 Mbps, 3.7 mA at 10 Mbps, 8.2 mA at 25 Mbps
Current per channel, 3 V0.8 mA maximum up to 2 Mbps, 2.2 mA at 10 Mbps, 4.8 mA at 25 Mbps
Pulse width distortion3 ns maximum, channel to channel matching 3 ns
Transient immunityover 25 kV per microsecond common mode
Isolation2500 V rms for one minute per UL 1577, VIORM 560 V peak
Package and rangenarrow body 8-lead SOIC, minus 40 to plus 125 C

Eleven milliwatts at two megabits, eighty two at twenty five

Both channels at 5 V and up to 2 Mbps draw 2.2 mA in total, 11 mW, while the same pair at 25 Mbps draws 16.4 mA, 82 mW, which is 7.5 times the power for 12.5 times the rate. Per unit of traffic the 25 Mbps point costs 1.64 mW per Mbps per channel, so a link that runs at 1 Mbps but is specified at the top of the range has paid for seven times the current it needs. The clock rate is therefore a power decision as much as a timing decision, and a bus that can be run at 1 Mbps instead of 10 Mbps saves 2.6 mA per channel at 5 V.

Three nanoseconds inside a forty nanosecond bit

At 25 Mbps one bit is 40 ns, and 3 ns of pulse width distortion is 7.5 percent of it, which is the budget left for the cable, the receiver threshold and the clock recovery on the far side. At 1 Mbps the bit is 1000 ns and the same 3 ns is 0.3 percent, so the distortion figure only becomes the limiting term at the top of the rate range. The 3 ns channel to channel matching is the separate specification that matters when two channels carry a clock and its data: a 3 ns skew between them is 7.5 percent of a bit at 25 Mbps and it eats the same margin as distortion does, which is why the pair should be treated as a differential timing group.

Two channels one way is not a bus

A 2/0 channel split gives a command path and a strobe, or a clock and a data line, in one direction only. A serial peripheral interface needs both directions and a chip select, which is three channels in two directions, so the part for that job is the ADuM1201 with a 1/1 split or the three channel parts in the same family. Reading the direction split from the order code before the board is laid out is cheaper than finding out that the return data line has no channel. The wide body parts in the same family carry higher ratings for mains referenced work, while this narrow body is aimed at functional isolation between two boards on the same chassis.

Before the order goes out

The ADuM1200 and ADuM1201 share a body and a pin out and differ only in direction split, so a bill of materials that lists the family without the last digit has not specified the part. The pin to pin cross reference lists the isolators that share this 8-lead footprint and the direction each carries, the BOM shortage recovery page is the place to start when the narrow body parts are on allocation, and the analog and mixed signal category page holds the rest of the isolation family.

Request Quote — In Stock, 100% New & Original, Full Warranty