Contact Us

ADP160ACBZ-3.3-R7

Brand: Analog Devices
Analog Devices ADP160ACBZ-3.3-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADP160ACBZ-3.3-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADP160ACBZ-3.3-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADP160ACBZ-3.3-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADP160ACBZ-3.3-R7: 560 nA of Quiescent Current and 150 mA of Output

The ADP160ACBZ-3.3-R7 is a CMOS linear regulator from Analog Devices with a 3.3 V fixed output and a 150 mA maximum load. Quiescent current is 560 nA with no load and 860 nA with a 1 microamp load, shutdown current is under 50 nA typical, the input range is 2.2 V to 5.5 V, and dropout is 195 mV at 150 mA. Initial accuracy is plus or minus 1 percent and accuracy over line, load and temperature is plus or minus 3.5 percent. The part is stable with 1 microfarad ceramic capacitors on input and output, rejects 72 dB at 100 Hz, has current limit and thermal overload protection, and includes a switched resistor that discharges the output when the regulator is disabled. Fixed outputs run from 1.2 V to 4.2 V in fifteen steps, and the family is offered in a 5-lead TSOT and a 4-ball 0.5 mm WLCSP.

Below 100 microamps the quiescent current is the efficiency

From a 5 V input to a 3.3 V output, the ideal efficiency is 66 percent, and the quiescent current is what turns that into something lower at light load. At 1 microamp of load the 860 nA of supply current is almost as large as the load, so the efficiency is 35.5 percent. At 10 microamps it is 60.8 percent, at 100 microamps 65.4 percent, and from 1 mA upward it sits at the 66 percent the ratio allows. The 560 nA is 2.8 microwatts at 5 V, which over a year is 4.9 mAh, and that is the number to compare against a coin cell or a harvested source rather than the milliamps the load draws when it wakes.

195 mV of dropout puts the minimum input at 3.495 V

A 3.3 V output at 150 mA needs at least 3.495 V at the input, so a 3.6 V rail leaves 105 mV of margin and a 3.3 V rail cannot supply this part at full load at all. That single line decides whether the 3.3 V option is the right one: from a 5 V rail there is plenty of headroom and 0.255 W is dissipated in the package at full load, from a lithium cell the regulator drops out and the output follows the battery down. The 50 nA of shutdown current and the output discharge resistor are the two features that matter in a battery product, because they decide how fast the rail collapses when the system goes to sleep.

One percent at 25 C is not the number a production line sees

The initial accuracy of plus or minus 1 percent is 33 mV at 3.3 V and it applies at room temperature with a nominal load. Over line, load and temperature the window is plus or minus 3.5 percent, which is 115.5 mV. A load that needs 3.3 V plus or minus 2 percent cannot be supplied by this part across temperature, and a load that needs plus or minus 5 percent can. The 72 dB of rejection at 100 Hz turns 1 V of ripple into 251 microvolts, and that figure falls with frequency, so a switching supply in front of this regulator has to be checked at the switching frequency rather than at 100 Hz.

ParameterPublished valueWhat it decides
Output3.3 V fixed, 150 mANeeds 3.495 V in at full load
Quiescent current560 nA no load, 860 nA at 1 microamp35.5 percent efficiency at 1 microamp from 5 V
ShutdownUnder 50 nA typicalSleep current of the whole rail
Accuracy1 percent initial, 3.5 percent over all conditions33 mV against 115.5 mV at 3.3 V
Dropout195 mV at 150 mA0.255 W dissipated from 5 V
Rejection72 dB at 100 Hz251 microvolts from 1 V of ripple
Capacitors1 microfarad ceramic, stableSmall footprint, no tantalum
Output dischargeSwitched resistor on disableRail collapses at shutdown

Which order code has the discharge resistor?

The ADP160 and the ADP161 include the switched discharge resistor and the ADP162 and ADP163 do not, so the zero before the last digit of the family name is the feature and not a revision. The code also carries the fixed output voltage and the tape and reel quantity, and the family is offered in both a 5-lead TSOT and a 4-ball WLCSP, so the package letter has to be checked against the footprint rather than assumed from the voltage. A substitution between the discharge and non-discharge versions changes how the rail behaves at shutdown, which is exactly the kind of change that passes a bench test and fails a power sequencing check.

Is it worth using at 150 mA when a switching regulator is more efficient?

At 150 mA from 5 V the linear regulator is 66 percent efficient and dissipates 0.255 W, so a buck converter would win on both counts. The reason to keep the linear part is noise: no switching ripple, no inductor, and 72 dB of rejection that removes what the upstream converter left behind. The usual arrangement is a buck for the heavy loads and this part as the post regulator for the analog rail, which is also where the 560 nA matters, because the analog rail stays alive while the rest of the system sleeps. The regulator range is on the power management cross reference, the checks for a substitution across the discharge variants are on the drop in replacement page, and the complete index is the analog and mixed-signal index.

Request Quote — In Stock, 100% New & Original, Full Warranty