Contact Us

TPS7A0325PYCHR

Brand: Texas Instruments
Texas Instruments TPS7A0325PYCHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0325PYCHR — Power Management & Signal Chain | Superb Automation

TPS7A0325PYCHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0325PYCHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0325PYCHR: the 2.5 V member in the 0.637 mm DSBGA body

The TPS7A0325PYCHR is the 2.5 V fixed output of the TPS7A03 line, packed in the four bump DSBGA coded YCH at 0.637 mm by 0.637 mm. It is the same silicon as the X2SON and SOT-23 members: 200 mA of output, 200 nA of quiescent current, a 1.5 V to 6.0 V input window and a 1.5 percent accuracy window over temperature. The difference is entirely physical, and on a wearable or a sensor tag that difference is the reason the part exists at all.

At 2.5 V the trim point suits a rail that feeds a sensor analog front end, a low power radio or a display bias, where 1.8 V is too low for the headroom and 3.3 V wastes current. The DSBGA body carries no leads, so the parasitic inductance between the die and the board is small, which is visible in the transient response at the higher edge rates.

Key electrical data for the 2.5 V point

Input range1.5 V to 6.0 V, 3.0 V minimum for full regulation at the full 200 mA
Output current200 mA, current limit 240 mA to 750 mA, short circuit 65 mA
Quiescent current200 nA typical, 250 nA maximum at 25 C, 220 nA in dropout
Shutdown current3 nA typical, 10 nA maximum, enable pin at 0 V
Accuracyplus or minus 1 percent at 25 C, plus or minus 1.5 percent over minus 40 to 125 C
Dropout at 200 mA400 mV maximum in the 1.8 V to 2.5 V band, 560 mV over the full range
Rejection and noise55 dB at 1 kHz into 30 mA, 130 uV RMS noise at 0.8 V out

Package, marking and reel data

BodyDSBGA YCH, 4 bumps, 0.637 mm by 0.637 mm, 0.35 mm pitch
Reel12000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishSNAGCU, tin silver copper with a gold flash over the bumps
Moisturelevel 1, 260 C peak reflow, unlimited floor life
MarkingK, a single character on a die this small

Where a 2.5 V, 200 mA rail belongs

The load profile that suits this part is a battery product with a 2.5 V analog domain: a pressure or gas sensor bridge, an instrumentation amplifier, a 2.5 V reference chain, or the supply of a sub gigahertz radio that is specified at 2.5 V rather than 3.3 V. Because the quiescent current is measured in nanoamps, the regulator can stay enabled between transmissions instead of being cycled, which removes the start up glitch from the radio's supply and shortens the wake sequence.

Two numbers decide whether the 2.5 V point regulates on a given battery. The dropout at 200 mA is 400 mV maximum in the 1.8 V to 2.5 V band and 560 mV at the hot end, so a single cell lithium pack that falls to 2.9 V still regulates, and one that falls to 2.8 V does not. The dissipation at 3.3 V in and 200 mA out is 160 mW, which the DSBGA body passes through the bumps to the board copper; without a copper landing under the bumps the junction runs far hotter than the data sheet thermal table assumes.

Buyer questions on the 2.5 V DSBGA code

Can this replace the X2SON version on the same board? No. The die is identical but the footprint is not, and the DSBGA needs a 0.35 mm pitch landing pattern that the X2SON board does not have. The two codes are alternatives when the board is drawn, not at the rework stage.

Why is the reel 12000 pieces rather than 3000? That is the packing the vendor publishes for the YCH body. A prototype quantity therefore has to come from a broken reel or from a distributor who repacks, and the date code and moisture history of a repacked strip should be recorded.

Does the part need an input capacitor? It runs without one, but a 1 uF ceramic at the input is the recommendation whenever the source impedance exceeds half an ohm or the regulator sits more than a few centimetres from the battery connector.

Buying the DSBGA body

Bare die scale packages are the first parts to go short when a wearable programme ramps, so the drop in replacement check is the page to read before a substitute is approved: it sets out the footprint, the bump pattern and the electrical window that have to match. Where the reel size is the obstacle rather than the silicon, kitting splits a 12000 piece reel into the quantity a pilot line actually needs.

The dropout window is the figure to plan around at 2.5 V. In the 1.8 V to 2.5 V band the maximum is 400 mV up to 85 degrees and 560 mV at the hot end, so a lithium cell that has fallen to 3.0 V still regulates and one at 2.8 V does not. Because the DSBGA body has no leads, the parasitic inductance between the die and the board is small, and that shows up in the recovery from a fast load step rather than in the steady state figures. A board that runs the part near its current limit should also account for the 240 mA minimum limit, which is close enough to the 200 mA rating that a cold start into a capacitive load can trip it.