LT3795IFE#TRPBF
Product Specifications
LT3795IFE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3795IFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3795IFE#TRPBF: 110 V LED controller with spread spectrum
LT3795IFE#TRPBF is the I grade of a 110 V constant current controller for LED strings, in the 28 lead TSSOP with exposed pad, on tape and reel. It drives an external low side N channel FET from an internal 7.7 V rail, senses LED current at 250 mV full scale with a rail to rail common mode, and carries spread spectrum modulation for emission compliance. The 3000 to 1 PWM dimming ratio is the number most buyers quote.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 4.5 V to 110 V |
| LED current sense | 250 mV full scale at 243 mV to 257 mV |
| Overcurrent threshold | 375 mV, 50 percent above full scale |
| Voltage reference | 2.015 V, 1.97 V to 2.06 V |
| Feedback regulation | 1.250 V, 1.230 V to 1.270 V |
| Gate drive supply | 7.7 V internal regulator, 18 mA at 110 V |
| Minimum on and off time | 210 ns and 160 ns |
| Quiescent current | 2.9 mA typical, 3.5 mA maximum, 10 uA in shutdown |
| Package and thermal | 28 lead TSSOP, theta JA 30 C/W, theta JC 10 C/W |
| Temperature grade | I, guaranteed minus 40 C to 125 C |
Two hundred and fifty millivolts in the LED return
At 250 mV full scale, a 1 A string needs a 0.25 Ohm sense resistor and dissipates 250 mW; at 350 mA the resistor is 0.714 Ohm and the loss is 87.5 mW. On a 90 V string at 350 mA the load is 31.5 W, so the sense loss is under 0.3 percent and the choice of resistor is really about the tolerance.
A one percent resistor at 250 mV is 2.5 mV of threshold error, which is 1 percent of the LED current. That is why this part can hold plus or minus 3 percent current regulation with an ordinary resistor.
Duty cycle limits at 400 kHz
At 400 kHz the period is 2.5 microseconds, so the 210 ns minimum on time sets an 8.4 percent floor on duty and the 160 ns minimum off time a 6.4 percent ceiling, which leaves 8.4 to 93.6 percent usable. A 110 V input to a 90 V string at 350 mA sits at 82 percent, inside the window but not far from it.
Above 93.6 percent the part cannot regulate and the string current falls, which is why a 110 V rail driving a 100 V string is a dropout question rather than a regulation one.
Spread spectrum and the 7.7 V rail
The internal regulator holds 7.7 V at 110 V in, which is 7 percent of the input, and it can source 18 mA. That current is what charges the external FET gate, so 18 nC of gate charge is the ceiling at 1 MHz, and a larger FET has to run at a lower frequency.
Spread spectrum modulation moves the switching frequency by up to 30 percent, which spreads the emission peak. It costs a little efficiency and it is the difference between passing a conducted emission test and adding a filter.
Two pages worth reading before a purchase order goes out are the power management cross reference and medical device components; the first lists what else fits the socket, the second is the test sequence for a drop in, and defense grade components covers the case where the shortage is already on the line.
Two questions buyers ask
Is the 250 mV sense threshold adjustable? The CTRL pins scale it: 250 mV at full CTRL, 225 mV at nine tenths, 125 mV at half and 25 mV at one tenth. That is the analogue dimming path, separate from the PWM pin.
What limits the input voltage? The 110 V rating of the pin and the external FET. The controller's own dissipation at 110 V is 385 mW, an 11.6 C rise in the TSSOP.