LT3799IMSE#TRPBF
Product Specifications
LT3799IMSE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3799IMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3799IMSE: Reading the Grade Letter on an Offline LED Controller
On the LT3799 datasheet the E and I codes are both listed at minus 40 C to 125 C, and the junction limit for the family is 125 C, so the letter does not buy a wider window here. What it does buy is the industrial screening label and, in practice, availability. The part itself is the critical conduction mode offline flyback LED controller with active power factor correction, TRIAC dimming, a 100 mV current limit and a 25 kHz to 300 kHz oscillator. A buyer choosing between the two codes should be looking at the transformer and the thermal path, not at the temperature column.
Published values
| Parameter | Value |
|---|---|
| Temperature range | I minus 40 C to 125 C, E the same range in this order table |
| Junction limit | 125 C, no 150 C grade in this family |
| Sense current limit | 96 to 106 mV |
| Feedback threshold | 1.22 to 1.29 V |
| Input turn-on and turn-off | 23 V and 12.3 V, 10.7 V hysteresis |
| Oscillator range | 25 kHz to 300 kHz, 20 kHz backup, critical conduction mode |
| Maximum oscillator period | 3.33 us at 300 kHz, 40 us at 25 kHz |
| Shunt regulator | 25 V, 15 mA |
| Power factor | 0.97 typical |
| Output range | 4 W to over 100 W with external parts |
| Thermal resistance | 50 C/W junction to ambient |
| Package | 16-lead MSOP with exposed pad, MSE |
The 125 C junction is the real constraint
There is no 150 C grade of this part, so the junction ceiling of 125 C applies whatever the letter says. At 50 C/W in a 60 C enclosure the dissipation budget is 1.3 W, and at 85 C it is 0.8 W. A 20 W LED driver at 85 percent efficiency loses 3 W, most of it in the transformer, the diode and the switch, so the controller only fits inside that budget if it is kept away from the hot parts and given copper of its own.
That is the reason the exposed pad matters here more than the grade letter. The pad is the only low resistance path out of a 16-lead MSOP, and a 50 C/W number assumes it is soldered to a plane rather than left floating on a thermal relief.
What critical conduction mode does to the magnetics
In critical conduction mode the current returns to zero every cycle, so the peak current is twice the average and the transformer stores the energy per cycle rather than passing it continuously. The peak current, not the average, sizes the switch and the sense resistor, which is why a 1 A output at a 4 to 1 ratio draws a much larger primary peak than the same power in a continuous mode converter.
The oscillator ceiling of 300 kHz sets the shortest period at 3.33 us and the floor of 25 kHz sets the longest at 40 us. A transformer that saturates at the low frequency end will saturate at start-up and at the bottom of the dimming range, so the check is at 25 kHz rather than at the nominal operating point.
Dimming and the fault pin
TRIAC dimming changes the conduction angle of the input waveform, and the part follows it by modulating the current reference. Deep dimming reduces the on time to a small fraction of the mains half cycle, and at that point the input filter and the bleeder become the limiting parts rather than the controller. The 0.5 W no load figure is the relevant number for a dimmer that is left at the bottom of its range.
Open and shorted strings are reported on the fault pin, which is an open drain output. In a system that has to latch off rather than retry, that pin drives the enable of the upstream switch, and the retry behaviour is set by the timer network rather than by the fault pin itself.
When an order code in this family cannot be found, the power management cross reference lists what else does the same job, BOM shortage recovery covers what to check before a part is dropped into an existing board, and component obsolescence management is the route we take on a live shortage.
Two questions buyers ask
Is the I code worth the premium over the E? On this datasheet both are listed at minus 40 C to 125 C, so the choice is price and availability rather than temperature. The junction ceiling of 125 C applies to both.
What limits the output power? The external switch, the transformer and the thermal path, not the controller. The datasheet describes the family as covering 4 W to over 100 W with external components chosen accordingly.