TPS7A0325DQNR3
Product Specifications
TPS7A0325DQNR3
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A0325DQNR3 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A0325DQNR3: a 2.5 V 200 mA nanopower regulator in a 1 mm square body
TPS7A0325DQNR3 is a fixed 2.5 V low dropout regulator from the same 200 nA family as the 3.3 V member, in the smallest body the family offers in a X2SON (DQN) body of 4 pins. Input range is 1.5 V to 6.0 V, output is fixed at 2.5 V, accuracy is 1.5 per cent over temperature and the dropout is 270 mV maximum at 200 mA on the 3.3 V member of the same silicon, so a 2.5 V rail from a 3.3 V bus has more than a volt of headroom. Quiescent current is 200 nA and stays there in dropout, shutdown current is 3 nA, and a 1 microfarad ceramic output capacitor is enough for stability. The X2SON body measures 1.0 mm by 1.0 mm with 4 pins and no enable pin.
Order code and package
| TPS7A0325DQNR3 | the 2.5 V fixed member in the 4 pin X2SON body, 3000 pieces on a large reel with marking Q3, which is the string a 2.5 V rail orders in the smallest body |
| TPS7A0325PDQNR3 | the same 2.5 V die with a P indicator in the string, printed on the same 3000 piece reel and the same body, which is the row most distribution stock is drawn from |
| TPS7A0325PDBVR | the 2.5 V member in the 5 pin SOT-23 body, with the enable pin brought out, for a board that needs to switch the rail off |
| TPS7A0333 and TPS7A0330 | the 3.3 V and 3.0 V members of the same family, same table and same bodies, so a board that moves its rail by 300 mV keeps its footprint |
| TPS7A02 family | the 25 nA member of the wider nanopower range, which is a different die with a lower quiescent current and a slower transient response, so the two are not interchangeable on a rail that needs the 10 microsecond settling |
| Body height | 0.4 mm in the X2SON, which is why the part appears on the back of a module or under a shield can where a SOT-23 does not fit |
Electrical parameters that decide the application
| Input voltage | 1.5 V to 6.0 V recommended, with an absolute maximum above that, so a 5 V rail with tolerance and a single cell lithium rail are both inside the window |
| Output voltage | 2.5 V fixed on this code, from a family table of 0.8 V to 5.0 V in 50 mV steps |
| Output current | 200 mA, limited by the thermal path of a 1 mm square body more than by the pass element |
| Quiescent current | 200 nA typical while regulating and while in dropout, which is the property that separates this family from the microamp class |
| Shutdown current | 3 nA typical on the bodies that carry an enable pin, which is below the self discharge of most cells |
| Dropout voltage | 270 mV maximum at 200 mA on the 3.3 V output, and lower on the 2.5 V output because the pass element has less to drop |
| Accuracy | 1.5 per cent over the full junction range, which is a logic rail figure and not a reference figure |
| Transient response | a 1 mA to 50 mA step settles inside 10 microseconds with about 80 mV of undershoot, quoted with a 1 microfarad output capacitor |
| Output capacitor | 1 microfarad ceramic or larger, with no ESR window to hit beyond a standard X5R or X7R part |
| Enable pin | present on the SOT-23 and DSBGA bodies and absent on the 4 pin X2SON, so the body decides whether the rail can be switched |
| Reverse current | blocked while the part is disabled, which keeps a biased output from feeding a dead input |
| Temperature | minus 40 C to 125 C junction, which covers an outdoor sensor and an indoor module with the same order code |
Voltage options and bodies in this family
| TPS7A0325DQNR3 | this order code, 2.5 V fixed in the 4 pin X2SON body, 3000 pieces on a large reel with marking Q3 |
| TPS7A0325PDQNR3 | the same 2.5 V die with the P indicator in the string, same body and same reel, which is the row most distribution stock comes from |
| TPS7A0325PDBVR | the 2.5 V member in the 5 pin SOT-23, which adds the enable pin and hand placeability |
| TPS7A0333 | the 3.3 V member, same table and same bodies, so a rail can move 800 mV without a footprint change |
| TPS7A02 family | a different die with 25 nA of quiescent current and a slower transient response, which is not a drop in replacement on a rail that needs the 10 microsecond settling |
| Headroom | at 3.0 V of input a 2.5 V rail holds; at 2.7 V of input the headroom is 200 mV and the rail starts to follow the input down |
| Body height | 0.4 mm in the X2SON against 1.1 mm in the SOT-23, which is a mechanical decision before it is an electrical one |
Points to check before this part goes on a BOM
The 0.4 mm body height is a mechanical decision before it is an electrical one. On a module that has to fit under a shield can, or on the back of a board that sits 0.5 mm from a chassis, the X2SON is the only body in this family that fits. The SOT-23 alternative is 1.1 mm tall and changes the mechanical stack, which is a change no electrical review will catch.
A 2.5 V rail from a 3.3 V bus is comfortable, from a lithium cell it is not. At 3.0 V of cell voltage the headroom is 500 mV and the dropout at 200 mA is under 300 mV, so the rail holds. At 2.7 V of cell voltage the headroom is 200 mV and the rail starts to follow the cell down, which is the point where the product has to decide whether it shuts down or keeps running out of regulation.
200 nA does not survive a bad capacitor choice. A ceramic with a high leakage, or an electrolytic on the output, can draw more than the regulator itself. On a nanopower rail every component on the net is part of the sleep budget, and the capacitor is usually the second largest contributor after the load.
There is no enable pin on this body. The 4 pin X2SON is live as soon as the input passes the lockout. A product that needs the rail off during shipping, or that sequences rails at power up, has to use the 5 pin body or put a load switch in front.
The transient figure is not a load regulation figure. A step from 1 mA to 50 mA produces 80 mV of undershoot that recovers in microseconds. A continuous 50 mA load produces a DC error set by the loop gain. Both are in the document and they are not the same measurement.
Being in the same family does not make two parts interchangeable. The TPS7A02 draws 25 nA and settles an order of magnitude slower than this die. A board that swaps one for the other to save a hundred nanoamps trades away the transient response that a radio transmit slot depends on.
Rails that stay on for the life of the product
A water meter, a heat cost allocator, a door sensor and a smoke alarm all have a rail that is never switched off. The regulator on that rail sets the replacement interval for the battery, and the number that matters is the quiescent current plus the load standby current, not the current rating. A 200 nA regulator with a 1 microamp load gives a 1.2 microamp total, and that is the figure the battery budget uses.
The second property that matters on those products is behaviour in dropout. As the cell falls, a regulator that keeps its quiescent current low lets the microcontroller see the rail sag slowly and shut down in order, rather than losing regulation abruptly and resetting in the middle of a measurement.
Choosing between this body and the SOT-23
The SOT-23 gives the enable pin and hand placeability. The X2SON gives 0.4 mm of height and a smaller pad area. Both are in the same data sheet, both carry the same electrical table, and neither is available in the footprint of the other. A product that plans to move from pilot to volume should place both footprints on the first board, because the alternative is a re-spin at the point where the schedule has no room for one.
Where this order code fits
a 2.5 V rail in a battery powered sensor, meter or wearable where the sleep current sets the battery interval and the body height is fixed by the enclosure Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
What input does a 2.5 V rail need? 1.5 V is the floor of the operating window, but holding 2.5 V at 200 mA needs the input above about 2.8 V because of the dropout. A 3.3 V bus is comfortable, a single lithium cell holds the rail down to about 2.7 V.
Can this part be shut down? Not in the 4 pin X2SON body, which has no enable pin. The 5 pin SOT-23 version of the same die carries the enable and draws 3 nA in shutdown.
How much current does it draw with no load? 200 nA typical while regulating, and the same figure while in dropout. The 3 nA shutdown figure applies only to the bodies with an enable pin held low.
Is the 2.5 V output available in 50 mV steps? The family table runs 0.8 V to 5.0 V in 50 mV steps, so a rail at 2.45 V or 2.55 V is also a catalogue part. The exact string differs by a digit inside the part number, so it is worth checking before a rail is fixed at 2.5 V.
How does it behave when the load steps from sleep to transmit? A 1 mA to 50 mA step produces about 80 mV of undershoot that recovers within 10 microseconds, so a radio slot leaves the rail inside a few per cent as long as the output capacitor is at least 1 microfarad.
What does SUPERB state on the offer for this line? The exact ordering string, the body, the reel quantity and the date code, because the 4 pin and 5 pin versions of the same 2.5 V die are separated by three characters and by the presence of the enable pin.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Consolidation page sets out the checks that keep a substitute from failing on the bench.