Contact Us

LT3755IMSE-2#TRPBF

Brand: Analog Devices
Analog Devices LT3755IMSE-2#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3755IMSE-2#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3755IMSE-2#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3755IMSE-2#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3755IMSE-2: The Improved Open LED Status Pin on a 75 V LED Controller

The LT3755 family is the 40 V input, 75 V output member of the LED controller line, and the minus 2 suffix is the variant with the improved open LED status pin. It senses string current at the high side with a 100 mV threshold, regulates 1.25 V on the feedback pin when the string is in constant voltage, and switches from 100 kHz to 1 MHz with a 170 ns minimum off time. This order code is the I grade in the 16 lead MSOP, guaranteed from minus 40 C to 125 C junction, and it is the one to specify when a fixture has to report a failed string to a controller rather than just stop regulating.

Published values

ParameterValue
Input range4.5 V to 40 V
Output voltageup to 75 V
Current sense100 mV high side, 96 to 103 mV full scale
FB regulation1.220 to 1.270 V, 1.250 V typical
Open LED threshold50 mV below the feedback point, 1.200 V
Overvoltage threshold60 mV above the feedback point, 1.310 V
Sense amplifier common mode2.9 V to 75 V
Short circuit threshold150 mV typical across the sense resistor
Switching frequency100 kHz to 1 MHz
Minimum off time170 ns
Gate drive supply7.15 V regulator, 34 mA current limit
Package and thermal16 lead MSOP, 43 C/W, 125 C maximum junction
GradeI, guaranteed minus 40 C to 125 C junction

100 mV of sense voltage decides the resistor and the loss

At a 100 mV full scale threshold the sense resistor follows the string current directly: 66.7 mOhm for 1.5 A and 50 mOhm for 2 A, which burns 150 mW and 200 mW respectively. That is a real tax on a 30 W string and it is why the high side threshold is kept low, but it also means the amplifier's offset and the resistor's tolerance are a larger share of the error than they would be at 250 mV. A 0.5 percent resistor plus the 96 to 103 mV window gives about 4 percent of current error before anything else, and the CTRL pin, which spans 0 to 1.1 V for analog dimming, is where that error can be trimmed out.

The common mode range is 2.9 V to 75 V, so the sense resistor can sit at the top of a 75 V string, which is what makes high side sensing worth the extra pins. Below 2.9 V the amplifier is out of range, so a buck mode string that runs near ground needs the resistor positioned above the threshold, not at the bottom.

What the minus 2 suffix changes: the open LED pin

The status pin is an open collector pull down that asserts when the feedback pin falls 50 mV below regulation, and the minus 2 part improves its behaviour. In practice the improvement shows up at the edges: the threshold is defined with the same 65, 50 and 40 mV window and the pin's low output is specified at 200 mV with 0.5 mA, so a controller reading it sees a clean logic low without a pull up fight. The overvoltage side is the mirror image, with the output disconnect driver pulled low when the feedback pin rises 60 mV above its point, which is the protection that opens the string when a LED fails open.

That second function is the one that saves a fixture. Without it, an open string lets the boost run to its maximum output and the remaining LEDs see the full compliance voltage. With it, the disconnect FET opens within one PWM cycle and the converter stops delivering current, which is why the PWMOUT pin is specified to be driven either to ground or to the 7.15 V internal rail.

3000 to 1 dimming and what it costs in the loop

At 200 Hz, a 3000 to 1 range means a 1.67 us on pulse. The gate driver can produce it: the 170 ns minimum off time is a tenth of that pulse, and the 7.15 V rail with a 34 mA current limit charges the FET gate quickly. The limit is the current loop, which needs several switching periods to settle at each pulse, so deep dimming at low frequency works better than deep dimming at high frequency. A 1 MHz switching frequency with a 1.67 us pulse has only 1.7 periods in it, and the current never reaches its regulated value, which shows up as a dimming curve that flattens at the bottom.

Two pages worth reading before a purchase order goes out are the power management cross reference and the ADI second source page; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to reduce component cost covers the case where the shortage is already on the line.

Two questions buyers ask

Can it drive a 75 V string from a 12 V input? Yes, in boost mode, and the 75 V output rating is the ceiling for both the string and the sense resistor's common mode. The duty cycle at 12 V to 75 V is 84 percent, which at 1 MHz is 160 ns of off time, just inside the 170 ns minimum, so a 12 V to 75 V converter has to run at a lower frequency or use a tapped inductor.

Does the open LED pin need an external pull up? Yes, it is an open collector pull down. A 10 k pull up to 3.3 V is the usual choice, and the pin sinks 0.5 mA at 200 mV, so the resistor value is not critical. The pin's absolute maximum is 12 V, which rules out pulling it to a 24 V rail directly.