Contact Us

LT3757AIMSE#TRPBF

Brand: Analog Devices
Analog Devices LT3757AIMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3757AIMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3757AIMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3757AIMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3757AIMSE: What the A Suffix Changes, and What It Does Not

The LT3757A is the same controller as the LT3757 with improved load transient response, and that single sentence is the entire published difference: input range, feedback points, sense threshold, minimum on and off times, oscillator range and package are identical. The A is the version to specify on a new build because the transient behaviour is better for the same price class, and it is the version that needs a second look when it is substituted into a board that was compensated for the non A part. This order code is the I grade in the 10 lead MSOP, guaranteed over minus 40 C to 125 C junction.

Published values

ParameterValue
Input range2.9 V to 40 V
Feedback point1.6 V positive, minus 0.800 V negative
SENSE current limit110 mV typical
Compensationexternal VC network, current mode
Minimum on and off time220 ns each
Switching frequency50 kHz to 1 MHz
Transconductance230 uS typical
Gate drive supply7.2 V regulator, 17.5 V overvoltage lockout
Quiescent current2.2 mA maximum, 1 uA shutdown
Package and thermal10 lead MSOP, 40 C/W, 150 C maximum junction
GradeI, guaranteed minus 40 C to 125 C junction
Difference from the non A partimproved load transient response, same pinout and same table

Why a better transient is not automatically a drop in

A current mode controller's transient response is set by the error amplifier transconductance, the VC pin impedance and the slope compensation, and the A version improves one of those without publishing a new number for the others. When the compensation network is carried over from a non A board, the loop crossover frequency moves, and a board that had 45 degrees of phase margin can end up with 30, which shows up as ringing after a load step rather than as instability. The check is a load step at the worst case input voltage with the actual inductor and output capacitor, looked at on the VC pin as well as the output.

The parts that do not move are the ones a buyer cares about: 1.6 V feedback, 110 mV sense limit, 220 ns minimum on and off times, 50 kHz to 1 MHz oscillator, 7.2 V gate regulator, 10 lead MSOP footprint. So the substitution is electrically safe and needs a loop check, not a new board.

The 110 mV limit and the switch current

Current is sensed in the FET source, so 110 mV is the switch current limit, not the output current limit. A 22 mOhm resistor gives 5 A of switch current and 550 mW in the resistor, which is a 1 W part at that current. In a boost the switch carries the input current, so a 12 V to 24 V converter at 2 A out draws about 4.2 A in and the sense resistor has to be sized for the switch current plus the ripple, not for the load. In a SEPIC the switch current is the sum of input and output current, which is the topology where the same resistor gives the least output current.

The 100 to 120 mV window across parts is plus or minus 9 percent, and that is the tolerance on the protection threshold. A build that needs a tight output current limit has to close a loop on the output instead of relying on the switch limit, which is what the FB pin is for.

Where the A version earns its price

Load transient matters when the output feeds a pulsed load: a radio that keys, a motor driver that changes direction, a LED string that is dimmed by switching the current in steps. In those cases the output capacitor and the loop's ability to respond decide the size of the capacitor, and a part with better transient response can use less capacitance for the same dip. On a steady load the A and non A parts behave the same, which is why the A is not worth a requalification on a product that is already in production.

When an order code in this family cannot be found, the power management cross reference lists what else does the same job, how to verify a drop in replacement covers what to check before a part is dropped into an existing board, and one stop BOM sourcing is the route we take on a live shortage.

Two questions buyers ask

Is the A version pin compatible with the non A part? Yes, same 10 lead MSOP and same pin functions, and every published electrical limit is the same. The difference is transient behaviour, so the substitution needs a load step check of the compensation network rather than a new board.

Can the LT3757A run a flyback? Yes. The controller drives a low side FET and senses its source current, which is the flyback primary current in a discontinuous or boundary mode, and the feedback pin accepts the opto or the auxiliary winding divider. The transformer has to be specified for the 220 ns minimum on time, otherwise the converter cannot deliver its full duty at the switching frequency chosen.