TPS78401QDBVRQ1
Product Specifications
TPS78401QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS78401QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS78401QDBVRQ1 automotive 300 mA adjustable regulator in SOT-23
The TPS78401QDBVRQ1 is the adjustable member of the TPS784-Q1 family in the five pin SOT-23 body, ordered on a 3000 piece reel. It sources 300 mA from an input between 1.65 V and 6.0 V, sets its output anywhere from 1.2 V to 5.5 V with two resistors, and holds 0.5 per cent typical and 1.7 per cent maximum accuracy over the full temperature range. Quiescent current is 25 microamp typical, rejection is 50 dB out to 100 kHz, and the die is qualified to minus 40 to plus 150 degrees junction.
Two features separate this family from a plain regulator. The first is the internal soft start of 500 microseconds, which limits the inrush into the output capacitor without an external part on a control pin. The second is the active output discharge, which pulls the rail down when the enable goes low instead of letting it float, so a peripheral that is being power cycled actually sees a low rail before it sees the next enable. Foldback current limit reduces the dissipation during an overload rather than holding a constant current into a short.
Key parameters printed in the SBVS387C document
| Input range | 1.65 V to 6.0 V |
| Output | 1.2 V to 5.5 V adjustable, fixed members from 0.65 V to 5.0 V in the family |
| Load current | 300 mA |
| Accuracy | 0.5 per cent typical, 1.7 per cent maximum over the operating range |
| Quiescent current | 25 microamp typical |
| Dropout | 115 mV maximum at 300 mA on the 3.3 V member |
| Rejection and soft start | 50 dB out to 100 kHz, internal soft start of 500 microseconds |
| Protection | Foldback current limit, thermal shutdown, active output discharge on disable |
Package, reel and top side marking
| Package | SOT-23, DBV body, five pins |
| Reel | 3000 pieces on a large tape and reel |
| Finish and moisture | Nickel palladium gold, moisture level 1, unlimited floor life |
| Temperature and marking | Minus 40 to plus 150 degrees junction, top side marking per the addendum row |
Where a 300 mA post regulator fits
This is the post regulator for a switching stage that has to hand over a clean rail to an analogue load: a sensor front end, an ADC reference buffer, or a radio's bias supply in a vehicle module. The 6 V input ceiling means it can sit directly on a 5 V bus with the transients that bus carries, and the 300 mA rating covers the load with margin. Because the output is adjustable, one code can serve a 1.8 V and a 3.3 V point on the same board, which is the argument for it over two fixed members when the reel count matters.
The constraint to respect first is dissipation. At 300 mA from 5 V into 1.2 V the part turns 1.14 W into heat, which the SOT-23 body will not hold without a copper area far larger than the package, so the input is normally a 1.8 V or 2.5 V rail rather than 5 V. The second constraint is the adjustable divider: the 1.7 per cent maximum accuracy is on the reference, and a 5 per cent divider dominates it, so one per cent resistors are the practical choice on a rail whose set point is specified. The how to verify a drop-in replacement page covers the measurements to repeat when a divider changes.
Questions buyers ask before ordering
Can it run from a 5 V bus into a 1.2 V load? Electrically yes, thermally only with a large copper area. 1.14 W in a five pin SOT-23 is beyond what the package holds on a narrow pad.
Does the output discharge work with the enable held low? Yes. The active discharge pulls the rail down when the enable is low, which is what makes a power cycle actually reach zero before the next enable.
Is the 0.65 V fixed output available in this body? The family has fixed members down to 0.65 V, but the orderable row and the body have to be matched. This code is the adjustable member in the five pin SOT-23, and the fixed points carry their own rows in the same addendum.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line, confirms the body and the reel from the addendum row, and keeps the date code with the certificate. A 300 mA post regulator fed from a rail that itself moves at start up will pass at the bench and show a step at the corner, so the input rail has to be settled before the divider is chosen. Send the rail, the load and the input bus through the power management cross reference page and the answer comes back with the code that matches the drawing and the reel that goes with it.