TPS55289RYQR
Product Specifications
TPS55289RYQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS55289RYQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS55289RYQR 30 V, 8 A buck-boost with an I2C interface for USB PD
The TPS55289RYQR is the digitally controlled member of the four switch buck-boost family: 3.0 V to 30 V input, 0.8 V to 22 V output programmable in 10 mV steps over I2C, 1 per cent reference accuracy, and an 8 A average inductor current limit, in a 3 mm by 5 mm QFN. It delivers 60 W from a 12 V input and 45 W from a 9 V input, with 96 per cent efficiency at 12 V to 20 V and 3 A.
The I2C interface is what makes it a USB PD part. A source that has to answer a request for 5 V, 9 V, 15 V or 20 V in fine steps can write the output voltage rather than switch a resistor divider, and the programmable output current limit up to 6.35 A in 50 mA steps lets the same hardware advertise different current capabilities on different contracts. Programmable power supply support is the feature that lets the output track a 20 mV step request from a phone.
The rest of the part is the same architecture as its pin strapped siblings: average current mode control, 200 kHz to 2.2 MHz switching with sync and spread spectrum, a 5 per cent accurate output current monitor, adjustable cable droop compensation, overvoltage protection, cycle by cycle peak limit, short circuit hiccup and thermal shutdown.
Key parameters from the SLVSGA9A document
| Input range | 3.0 V to 30 V |
| Output range | 0.8 V to 22 V programmable in 10 mV steps over I2C |
| Current limit | Programmable up to 6.35 A in 50 mA steps, against an 8 A average inductor limit |
| Power delivery | 60 W from 12 V input, 45 W from 9 V input |
| Efficiency | 96 per cent at 12 V to 20 V and 3 A |
| Reference accuracy | 1 per cent |
| Interface | I2C, with programmable power supply support for USB PD |
| Switching frequency | 200 kHz to 2.2 MHz by resistor, clock sync, optional spread spectrum |
| Package | 3.0 mm by 5.0 mm QFN, RYQ body |
Why 10 mV steps change the product
A fixed divider gives a fixed output, and a PD source built from one needs a switch matrix to offer four voltages. With 10 mV resolution the same converter covers the whole contract table and the fine adjustment that programmable power supply asks for, and the board loses the matrix. That is fewer parts, fewer failure modes and a smaller bill, which is why the I2C version exists.
The current limit in 50 mA steps works the same way on the other axis. A 65 W port that has to advertise 3 A at 20 V and 3 A at 5 V can set the limit per contract rather than sizing one resistor for the worst case, and the 5 per cent current monitor gives the source the feedback it needs to report actual delivery.
Cable droop and the monitor
Adjustable output compensation raises the output voltage as the load current rises, so the voltage at the end of a cable stays inside the contract window. Without it, a 1 A load on a 1 m cable with 200 milliohm of loop resistance loses 200 mV, which is enough to fail a PD compliance test at the low end of the window. The compensation is set against the cable resistance, so the host software and the cable have to be treated as one item.
The 5 per cent current monitor is accurate enough for reporting but not for a precision measurement, and the document says so. Programs that need better have to add a shunt, and the shunt has to be placed where the converter's own compensation does not fight it.
Where this part fits
USB PD adapters and car chargers, power banks with a display, and any product where the output voltage has to be set by software rather than by a resistor. Our desk keeps the family cross reference and the interface comparison, see power management cross reference and one stop BOM sourcing.
What to check before a purchase order
The I2C version and the pin strapped versions share a body and a footprint, so a substitution in either direction fits the board and changes the behaviour completely. Confirm the order code and the marking, confirm that the host has an I2C master on the right bus, and confirm the default output at power up, because a PD source that boots at 20 V before the contract is negotiated fails certification.
See incoming inspection plan for the receipt check, and component lead time solutions when the I2C version is short and the pin strapped one is not.
Questions that come up on this part
Does the I2C interface also carry fault status, is a common question. Yes, and the fault registers are what make a field failure diagnosable, so the host software should read them rather than only writing voltage. The second question is whether the part can start without I2C traffic. It can, on its default output, and that default has to be chosen with the certification requirement in mind.