TPS565201DDCR
Product Specifications
TPS565201DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS565201DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS565201DDCR 5 A at 500 kHz in a SOT-23-THIN body
The TPS565201DDCR is a 4.5 V to 17 V, 5 A synchronous buck in a 6 pin SOT-23-THIN package, 1.6 mm by 2.9 mm. It integrates a 31 milliohm high side and a 16 milliohm low side FET, which is roughly half the resistance of the 3 A parts in the same body, and it runs at a fixed 500 kHz. Control is D-CAP2 with no external compensation, and the light load behaviour is pulse skipping under the Eco-mode label.
Five amps out of a body this size is only possible because the two FETs are large relative to the die and because 500 kHz is a moderate frequency for the loss budget. The feedback reference is 760 mV with a 753 mV to 767 mV window, the output range is 0.76 V to 7 V, and the internal soft start is 1.0 ms. Shutdown current is 0.8 microamp typical and 5 microamp maximum.
The part is the workhorse of the low voltage rail in a small box: a 12 V input, a 1.0 V to 3.3 V output, and 4 A to 5 A of processor or FPGA load. It is not the lowest quiescent current device in the family and it is not the smallest, but it puts the current where the board needs it without an external compensation network.
Key parameters from the SLVSE71 document
| Input range | 4.5 V to 17 V, UVLO waking at 4.0 V to 4.3 V and shutting down at 3.3 V to 3.6 V |
| Output current | 5 A from a 31 milliohm high side and a 16 milliohm low side FET |
| Output voltage | 0.76 V to 7 V against a 760 mV reference, 753 mV to 767 mV window |
| Switching frequency | 500 kHz fixed, measured at 12 V in, 5 V out in continuous conduction |
| Current limit | 5.3 A minimum, 6.7 A typical and 8 A maximum on the cycle by cycle comparator |
| Quiescent current | 320 microamp typical and 510 microamp maximum non switching, 0.8 microamp shutdown |
| Soft start | 1.0 ms internal, no external capacitor |
| Protection timing | Hiccup on 1.8 ms, restart delay 14.9 ms, thermal shutdown at 172 degrees |
| Package | 6 pin SOT-23-THIN, 1.6 mm by 2.9 mm, DDC body, 3000 pieces on a large reel |
The enable pin is a divider, not a logic input
The enable pin on this device is not a simple digital input. It carries an internal resistance to ground of 120 kilohm to 400 kilohm, typically 245 kilohm, and the thresholds are 1.6 V rising and 0.8 V falling with a 5 V input. That combination means a resistor from the input rail to the enable pin sets a turn-on voltage directly, and the same pin can be pulled low by an open drain signal if the board needs a controlled sequence.
Two consequences follow. A divider that was copied from a part with a high impedance enable pin will turn on at the wrong input voltage, and a long trace to the enable pin will pick up switching noise because the impedance is a quarter of a megohm. Keep the node short, and if a divider is used, compute it against the 245 kilohm typical and then check the 120 kilohm and 400 kilohm ends for the turn-on window.
Undervoltage lockout sits at 4.0 V to 4.3 V rising, which is above a 3.3 V rail. A 3.3 V input is outside the intended range for this part, and a board that tries it will see the converter start and stop as the rail settles. The 4.3 V top of the wake window is the number to use when a 5 V rail has to survive a brownout.
Where this part fits
5 V and 3.3 V intermediate rails, processor cores at 1.0 V to 1.2 V, and any board that wants 5 A without a compensation network. Our desk keeps the cross reference for this class and the receipt checks that go with a six pin thin body, see power management cross reference and one stop BOM sourcing.
What to check before a purchase order
The DDC body is shared with several 3 A parts in the same family that run at 580 kHz, and the order code is the only field that separates them at goods inwards. The DDCR row is 3000 pieces on a large reel and the DDCT row 250 on a small one, so a prototype build needs the T row or a cut reel. Confirm the current limit against the inductor saturation current: the 8 A maximum of the window is well above the 5 A rating, and an inductor picked for 5 A will saturate during a fault before the hiccup counter trips.
Thermal margin is the second item. At 5 A from 12 V to 1.0 V the low side conducts for about 92 per cent of the period and dissipates roughly 0.35 W in the FET alone, and the body is 1.6 mm by 2.9 mm. On a two layer board with 1 oz copper the pad runs warm at 5 A in a 60 degree box, so the copper area matters as much as the part choice. See incoming inspection plan for the marking check.
Questions that come up on this part
Can it be used on a 3.3 V input, is the usual first question, and the answer is no, the lockout is above the rail. The second is whether the 5 A rating is continuous at 85 degrees. It is a junction rating, so the ambient figure depends on the copper and the airflow, and a board that needs 5 A at 85 degrees should measure the case temperature rather than trust the headline.
The third question is about the Eco-mode ripple. Below a few tens of milliamps the part skips pulses and the output ripple becomes a burst pattern at a low repetition rate. That is fine for a digital rail and is not fine for a rail that feeds a sensitive analog stage, where the 3 A always-conduction part in the same family is the better choice.