Contact Us

TPS549D22RVFR

Brand: Texas Instruments
Texas Instruments TPS549D22RVFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS549D22RVFR — Power Management & Signal Chain | Superb Automation

TPS549D22RVFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS549D22RVFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS549D22RVFR 40 A buck with the full PMBus command set

The TPS549D22RVFR is the 40 A PMBus member of the D-CAP3 family: 1.5 V to 16 V on PVIN, 4.5 V to 22 V on VDD, 2.9 milliohm high side and 1.2 milliohm low side FETs, in the 7 mm by 5 mm, 40 pin LQFN-CLIP. It is the same silicon family as the pin strapped 40 A device, with the strap pins replaced by a bus, and that is the whole difference a buyer has to care about.

The reference is trimmed 0.6 V to 1.2 V in 50 mV steps by VSEL, at 0.5 per cent against 0.9 V nominal over 40 to 125 degrees junction, and the sense is a true differential pair. Eight switching frequencies are available over PMBus from 315 kHz to 1.125 MHz, which is double the four settings the pin strapped version offers, and the extra settings are the ones that land between 650 kHz and 1.05 MHz where most 40 A rails actually want to run.

Standard VOUT_COMMAND and VOUT_MARGIN high and low commands are supported, along with pin strapping and on the fly programming, fault reporting and warning, NVM backup for selected commands, and a 1 MHz PMBus with packet error checking and SMB_ALRT.

Key parameters from the SLUSCI9A document

Input range1.5 V to 16 V on PVIN, 4.5 V to 22 V on VDD
Output current40 A continuous with 2.9 milliohm high side and 1.2 milliohm low side FETs
Output voltage0.6 V to 5.5 V, reference 0.6 V to 1.2 V in 50 mV steps by VSEL
Switching frequency315 kHz, 425 kHz, 550 kHz, 650 kHz, 825 kHz, 900 kHz, 1.025 MHz and 1.125 MHz over PMBus
Reference accuracy0.5 per cent against 0.9 V nominal over 40 to 125 degrees junction
Current limitRILIM resistor, temperature compensated, with an OC clamp behind it
Bus featuresVOUT_COMMAND and VOUT_MARGIN, fault reporting and warning, NVM backup, 1 MHz with packet error checking
Package40 pin LQFN-CLIP, 7 mm by 5 mm, RVF body, RoHS exempt

Pin strap version or bus version

The two 40 A devices share a body and a power stage, so the choice is an interface choice, not a performance choice. A board that never needs margining, never needs a frequency other than the four strap settings, and has no bus master should take the pin strapped part: fewer nodes to validate, fewer things that can be written wrong in the field. A board that has to be margined at test, that has to log its own faults, or that has to run between 650 kHz and 1.05 MHz should take this one.

The trap is a program that chooses the bus version for a future feature and then never populates a bus master. The rail still starts on its defaults, so the board works, but the NVM never gets programmed, and a later software change that expects a written configuration finds a device at factory settings.

40 A on 1.2 milliohm and what it means thermally

At 40 A the low side conducts for most of the period in a 12 V to 1 V conversion, and 1.2 milliohm at 40 A is 1.9 W in one device. The pad, the vias and the copper island are the path for that heat, and the document's thermal numbers assume a specific arrangement of all three. A common error is to keep the pad copper but cut the via array to fit a plane split, which raises the junction temperature by tens of degrees without changing anything visible on the bill.

Eco mode and forced continuous conduction are both selectable, and the choice changes the no load draw by roughly an order of magnitude. On a rail that must answer a fast load step from idle, forced continuous conduction is usually the right answer despite the loss.

Where this part fits

Processor, FPGA and ASIC core rails at 40 A per phase, DDR rails, and any board where the rail has to be margined and monitored. Our desk handles the second source and the drop in checks for this family, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

Three fields. The order code letter separates this device from the 25 A and 10 A members that share the body. The RVF suffix confirms the 40 pin 7 by 5 mm package. The compliance status is RoHS exempt on the published rows, which has to appear on the quote for any customer with a compliance clause. A fourth field is the moisture level, since these bodies are typically level 3 with a 168 hour floor life after the seal is broken.

See date code management for floor life and bake records, and component lead time solutions when the 40 pin body runs short.

Questions that come up on this part

Can the pin strapped part be dropped into a board built for this one, is a common question. Yes mechanically, and the board will regulate, but every bus feature disappears, so any test step that margins the rail has to be removed from the process. The second question is whether NVM survives a reflow. It does, and the store cycle is specified after assembly, not before.