Contact Us

TPS56221DQPR

Brand: Texas Instruments
Texas Instruments TPS56221DQPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS56221DQPR — Power Management & Signal Chain | Superb Automation

TPS56221DQPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS56221DQPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS56221DQPR 25 A at 14 V input in the same body as the 15 A part

The TPS56221DQPR is a 4.5 V to 14 V, 25 A synchronous buck in a 22 pin PQFN, 5 mm by 6 mm, built on NexFET power blocks inside the package. It is the higher current member of a pair that shares the body, the pinout and the control scheme with the 15 A device, so a board built for one can be re populated for the other if the inductor and the input bank were sized for the larger current.

Control is voltage mode with input feed-forward, and the loop compensation is external. The reference is 600 mV at 1 per cent, output goes down to 0.6 V, and the frequency is fixed by order code at 300 kHz, 500 kHz or 1 MHz. Soft start is programmable, prebiased startup is supported, and thermal shutdown is included.

Overcurrent protection uses the drop across the low side FET, with the limit set by a resistor from ILIM to ground. The value is measured during a calibration cycle at power up, so the offset of the sense path is trimmed out on every start. That is the same scheme as the 15 A member, and it is why the two behave identically during a fault even though the current rating differs.

Key parameters from the SLUSAH5D document

Input range4.5 V to 14 V, aimed at a 12 V intermediate bus with a transient allowance
Output currentUp to 25 A with integrated NexFET power blocks in the package
Output voltageDown to 0.6 V, set by the feedback divider against a 600 mV reference at 1 per cent
Switching frequencyFixed options of 300 kHz, 500 kHz and 1 MHz by order code
ControlVoltage mode with input feed-forward, external loop compensation
Current limitILIM resistor read during a power on calibration cycle, then compared against the low side FET drop
Package22 pin PQFN with PowerPAD, 5 mm by 6 mm, DQP body

What separates 15 A from 25 A on one footprint

The body and the pins are the same, so the difference on the board is the current path, not the outline. At 25 A the inductor carries roughly 1.7 times the current of the 15 A case, and the ripple current in the input ceramics rises with it. A board that was laid out for 15 A and then re populated for 25 A will usually work at room temperature and fail a thermal soak, because the copper under the pad and the via count were sized for the lower number.

Two settings have to change with the part: the ILIM resistor and the loop compensation. The current limit has to rise with the rating, and the compensation has to be recomputed because the power stage gain changes with the FET resistances and the inductor. Re using the 15 A resistor values gives a limit that trips early and a loop that is over damped, which reads on the bench as a slow transient rather than as an obvious fault.

Where 25 A single phase is the right answer

A 25 A single phase is cheaper in board area than two 15 A phases, and it needs one inductor rather than two, which matters when the height under a lid is the constraint. The cost is ripple: 25 A at 500 kHz needs more output capacitance for a given transient than two interleaved phases at the same total current, because the interleaving cancels part of the ripple in the capacitor. For a load that does not step hard, the single phase is the simpler answer.

At 1 MHz the inductor shrinks and the switching loss rises, so a 12 V to 1 V conversion at 25 A is normally run at 500 kHz. The 300 kHz option is for boards where efficiency at full load matters more than board area, and where the output bank can be large.

Where this part fits

12 V bus processors and FPGAs at 25 A, telecom line cards, and any board that wants one phase instead of two. Our desk keeps the family cross reference and the footprint comparison, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The DQP suffix is the 22 pin 5 by 6 mm PQFN, and the same product page covers three fixed frequencies, so the order code is the only place the frequency appears. Confirm the ILIM resistor against the inductor saturation current, confirm the compensation matches the output bank, and confirm the copper area under the pad against the 25 A thermal requirement rather than the 15 A one.

See incoming inspection plan for the receipt check, and component lead time solutions when one frequency option is short.

Questions that come up on this part

Is this a drop in for the 15 A device, is the usual first question. Mechanically yes, electrically only after the current limit and the compensation are changed. The second question is whether the part can run at 14 V input and 0.6 V output continuously. It can, but the on time at 1 MHz is short, so the 300 kHz or 500 kHz option is the safer choice at that ratio.