Contact Us

TPS77715PWP

Brand: Texas Instruments
Texas Instruments TPS77715PWP is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS77715PWP — Power Management & Signal Chain | Superb Automation

TPS77715PWP

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS77715PWP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS77715PWP 1.5 V 750 mA regulator in the 20 pin PowerPAD body

The TPS77715PWP is the same 1.5 V, 750 mA regulator as the SOIC member of the TPS777 family, mounted in the 20 pin HTSSOP body with an exposed thermal pad and offered in a 70 piece tube or on a 2000 piece reel with the R suffix. Electrically nothing changes: 260 mV of typical dropout at 750 mA on the 3.3 V point, 2 per cent tolerance, 85 microamp of quiescent current, an open drain reset with a 200 millisecond delay, and a current limit that reaches 2 A at the top of the band.

What changes is the thermal path. The PowerPAD sits on a copper area with vias, so the same 1.35 W that the eight pin body struggles to shed from a 3.3 V input is spread into the board and the junction runs cooler at the same load. That is the reason this body is chosen on dense boards where a copper pour beside an eight pin package is not possible, and it is also the reason the tube version exists: the 20 pin body is used in lower volumes where a 70 piece tube matches a build better than a 2000 piece reel.

Key parameters printed in the SLVS230G document

Output1.5 V fixed, with the same fixed and adjustable members as the SOIC body
Load current750 mA
Dropout260 mV typical at 750 mA on the 3.3 V member
Accuracy2 per cent over the specified conditions for fixed members
Quiescent current85 microamp typical across the load range
Current limit1.2 A typical, 2 A at the top of the band
Rejection and noise60 dB at 1 kHz, 54 microvolt RMS over 100 Hz to 100 kHz
ResetOpen drain, 200 millisecond delay, trip at 92 to 98 per cent of output

Package, reel and top side marking

PackageHTSSOP, PWP body, 20 pins, exposed thermal pad
Reel70 pieces in a tube for the plain PWP row, 2000 pieces on a large tape and reel for the PWPR row
Finish and moistureNickel palladium gold, moisture level 1 on the plain row and level 2 with a one year floor life on the R row
Temperature and markingMinus 40 to plus 125 degrees, top side marking PT77715

Where the 20 pin body changes the thermal answer

The 20 pin body carries extra ground and heat sink pins around the die, which is why the same silicon behaves differently on a board with limited copper. In practice the part is chosen when the 1.5 V rail feeds a bank of memory devices spread across the board and the regulator sits in the middle of them, so the copper that would have been used as a heat spreader is already committed to the memory. The reset output can then hold the memory controller until the rail is inside tolerance, which removes a supervisor from the bill of materials.

Two orderable rows exist and they are not the same product. The plain PWP row is a 70 piece tube at moisture level 1; the PWPR row is 2000 pieces on a large reel at moisture level 2 with a one year floor life. A line that orders by family name will receive whichever the distributor has, and the moisture level difference then becomes a floor life question in stores rather than a purchasing question. The reel letter is the field to quote, and the date code management page sets out how the two rows are kept apart at goods in.

Questions buyers ask before ordering

Is the tube version the same silicon? Yes. The PWP and PWPR rows differ in packaging and moisture level, not in the electrical table.

Does the thermal pad need vias? Yes. The pad is the only path from the die to the board, and a pad soldered to a surface layer without vias gives up most of the advantage the body was chosen for.

Can this replace the SOIC member without a board change? No. The 20 pin HTSSOP is a different footprint from the eight pin SOIC, so a replacement is a footprint change rather than a substitution.

Ordering this part through SUPERB

SUPERB supplies this regulator in either row, states which packaging the quote is against, and keeps the moisture level on the certificate so the stores decision is made with the fact rather than the assumption. A board that has to be reworked from the tube version to the reel version is a stores problem rather than an electrical one, so it is worth settling before the first kit is picked. Send the rail, the load and the annual quantity through the kitting service page and the answer comes back with the row, the reel and the date code.