Contact Us

BQ25188YBGR

Brand: Texas Instruments
Texas Instruments BQ25188YBGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25188YBGR — Power Management & Signal Chain | Superb Automation

BQ25188YBGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25188YBGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25188: the same 1 A charger in a package that does not need a fine line board

The BQ25188YBGR is an I2C controlled single cell linear charger with power path, ship mode, shutdown mode, battery tracking input regulation and a 3.0 V to 18 V input window. Electrically it sits in the same class as the BQ25186. The difference is the body: 8 balls in a 1.6 mm by 1.1 mm chip scale package.

That body matters for a reason the document states directly. The 8 ball package can be assembled on a conventional board process, so a product does not need a fine line substrate to use a 1 mm class charger. On a wearable or a sensor node where the rest of the board is ordinary FR-4 with 0.1 mm tracks, a 25 ball 0.4 mm pitch part forces the whole board up a class. This one does not.

The charge engine is the same story as its sibling: 5 mA to 1 A of charge current, a 0.5 per cent setpoint from 3.6 V to 4.65 V in 10 mV steps, three chemistries, a 55 milliohm battery FET and up to 3 A of system current through the path.

Key data for the BQ25188YBGR

FunctionSingle cell linear charger with power path, ship and shutdown modes
Input range3.0 V to 18 V operating, wide VIN support
Charge current5 mA to 1 A, I2C configurable
Voltage accuracy0.5 per cent, 3.6 V to 4.65 V in 10 mV steps
ChemistryLi-ion, Li-polymer and LiFePO4
Battery FET55 milliohms on resistance
System currentUp to 3 A discharge through the power path
VINDPMBattery tracking input regulation
NTCConfigurable profile thresholds with JEITA support
PackageDSBGA, 8 balls, 1.6 mm by 1.1 mm, marking B188
TemperatureMinus 40 to 85 C operating

Body and ordering data

BQ25188YBGR is the active production row: DSBGA YBG with 8 balls, 3000 pieces on a large tape and reel, SNAGCU finish, moisture level 1 at 260 C with no floor life limit, minus 40 to 85 C, marking B188. The .A row carries the same body and the same reel. The addendum prints the operating temperature of the plain row as a cross reference to the .A row rather than as a number, which is a text extract artefact and not a different rating.

The 85 C ceiling is the one real difference from the WSON sibling at 125 C. On a board where the charger sits next to a radio or a motor driver, that 40 degree gap is the whole decision. On a product where the charger is the only heat source, the smaller body wins on area.

Eight balls and what is not in them

An 8 ball body at this size has no room for a separate thermal pad, so the die is cooled through the balls and the copper under them. That limits the continuous charge current in a warm enclosure more than the register setting does. The part will not fail; the thermal loop cuts the current and the charge takes longer.

It also means the passive count has to be tight. There is no spare pin for a status LED or a second thermistor input, and the NTC network shares the pins that remain. Reading the pin list before committing the board is worth more than reading the feature list.

Where it fits in a build

Wearables, sensor nodes, handhelds and medical accessories where the board is ordinary FR-4 and the charger has to be small without forcing a finer substrate class. The medical device components page covers what a health accessory build usually asks about traceability and date codes.

For a product in a hot enclosure, the WSON version at 125 C is the safer choice even though it is larger. For a product that charges from a 12 V source at 1 A, neither linear part is right and a switching charger belongs in the socket instead.

The sourcing side of this part is covered on the PCBA quote checklist. For a board where the charger sets the substrate class, that page covers the questions we ask before a quote turns into a build.

Questions we get on this code

Does it really avoid a fine line board? Yes, that is stated in the document as a benefit of the 8 ball body. The ball pitch is coarse enough for a conventional process.

Can it run at 1 A continuously? Depends on the copper and the ambient. The electrical limit is 1 A, the thermal limit is lower in a sealed box.

What is the difference from the BQ25186? The charge engine is the same class, the body and the temperature rating differ. The WSON part reaches 125 C, this one 85 C.

Is ship mode the same as shutdown? No. Ship mode disconnects the pack with the lowest drain and can be exited from the button. Shutdown is a deeper state that needs an input to come back.