BQ25756RRVR
Product Specifications
BQ25756RRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ25756RRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ25756: the 70 V member of the same bidirectional controller family
The BQ25756RRVR is the wide voltage version of the buck boost charge controller. The input window is 4.2 V to 70 V, the pack can reach 70 V, and the supported profiles are one to fourteen Li-ion cells or one to sixteen LiFePO4 cells. Everything else is shared with the 36 V member: external NFETs, 200 kHz to 600 kHz switching, integrated loop compensation, MPPT, and reverse mode that regulates the input terminal from the pack.
Seventy volts is the number that opens the e-mobility market. A 14 cell Li-ion pack at 4.2 V per cell reaches 58.8 V, and a 48 V e-bike or e-scooter system sits right there. A 36 V controller cannot charge that pack, so the two strings are not interchangeable even though they share a body and a document.
The reverse mode on this part is what a product uses to present a source at its charging port. With the right register settings the pack drives the input terminal at a regulated voltage with a current limit, which is a USB PD extended range source or a direct feed to another pack.
Key data for the BQ25756RRVR
| Function | Bidirectional buck boost charge controller, external NFETs |
| Input range | 4.2 V to 70 V operating |
| Battery range | Up to 70 V, one to fourteen Li-ion cells, one to sixteen LiFePO4 cells |
| Switching frequency | 200 kHz to 600 kHz adjustable, external clock sync optional |
| MPPT | Automatic maximum power point tracking for solar charging |
| Reverse mode | Regulates the input terminal with a constant current limit |
| Compensation | Integrated loop compensation and soft start |
| Control | Stand alone or I2C, charge status indication |
| Package | VQFN, 36 pins, RRV body, marking BQ25756 |
| Temperature | Minus 40 to 125 C operating |
The other practical difference is the sense element and the current path. A 70 V stage needs a sense resistor rated for the power it dissipates at the full charge current, and a 1 milliohm part that passes the bench test at 5 A will drift at 400 W of input power. The controller reads the voltage across that resistor, so its temperature coefficient becomes a charge current error that no register can correct.
Body and ordering data
BQ25756RRVR is active and in production: VQFN RRV with 36 pins, 3000 pieces on a large tape and reel, SN finish, moisture level 1 at 260 C with no floor life limit, minus 40 to 125 C, marking BQ25756. The .A row carries the same body and reel.
The E version, which is the other die on this document, stops at 36 V. Both are 36 pin RRV parts with the same footprint, so a board built for one accepts the other and the difference only appears when the pack voltage exceeds the lower part's limit. That is a substitution risk worth flagging in any second source discussion.
Seventy volts changes the external parts, not just the die
The controller is rated for the voltage, and the FETs, the inductor, the sense resistor and the capacitors have to be too. A 60 V rated FET on a 58.8 V pack is at its limit before any ringing, and the switch node of a buck boost rings to twice the input on a hard transition. The voltage class of the power stage, not the controller, is usually the real cost driver on this board.
The 200 kHz end of the frequency range exists for the same reason: a 70 V stage switching at 600 kHz has switching losses that dominate, and the inductor that fits at 200 kHz is the one that keeps the stage cool. That is a larger inductor than a consumer product would tolerate.
Where it fits in a build
E-bikes, e-scooters, portable power stations at 48 V class, solar chargers for larger packs and any battery platform that has to source power back out of its charging port. The power management cross reference page lists the cell counts and voltage classes we compare.
A 24 V tool platform is served by the 36 V member at lower cost. Using this part on a 24 V pack spends money on voltage margin that the product never uses.
The sourcing side of this part is covered on the component lead time solutions. For a 48 V platform that cannot wait on one part, that page sets out how we check stock and packaging before a second source is proposed.
Questions we get on this code
Does it need a host? No. Stand alone operation sets the profile; I2C adds run time control and status.
Can it charge and discharge at the same time? The converter is bidirectional but the direction is a mode, not a simultaneous operation. Power flow is one way at a time.
What sets the reverse mode voltage? A register for the target and another for the current limit. Both have to be written before the mode is enabled.
Is the 70 V rating a transient figure? No, it is the operating input range. Transients above it need clamping at the connector, because the absolute maximum is only slightly higher.