Contact Us

BQ24013DRCR

Brand: Texas Instruments
Texas Instruments BQ24013DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24013DRCR — Power Management & Signal Chain | Superb Automation

BQ24013DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24013DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24013DRCR: a 1 A linear charger in a 3 mm square

The BQ24013DRCR is one member of the bqTINY family, a single-cell Li-Ion and Li-Pol linear charger with the pass FET, the current sensor and the reverse blocking circuit on one die. It takes an AC adapter or a USB source and charges the cell in three phases: a conditioning phase for a deeply discharged cell, a constant current phase, and a constant voltage phase that ends on a minimum current or on the internal timer. The 3 mm by 3 mm body is the reason the family exists: at 1 A of charge current there is nothing else on the board except the input and output capacitors, the two setting resistors and the status LEDs.

The family has five members, bq24010, bq24012, bq24013, bq24014 and bq24018, and they differ in which of the optional pins are brought out: a temperature sense input for a battery thermistor, a power good output, a TTL level charge enable, and a TTL level timer and termination enable. The package and the power stage are the same, so the choice between them is a choice about how much control the host gets, not about current or voltage. Once an order code is picked, the pin functions on the board are fixed.

Accuracy is quoted two ways in the same document. The feature list states plus or minus 0.5 percent voltage regulation accuracy, and the electrical table quotes a voltage regulation accuracy of 1 percent with the condition that the ambient is 25 C. Both numbers describe the same output. A product that has to hold the cell voltage inside a tight window over temperature should use the table row and its conditions, not the feature line.

Key data for the BQ24013DRCR

FunctionSingle-cell Li-Ion and Li-Pol linear charger, pass FET and current sensor integrated
Charge current100 mA to 1000 mA output range, set by a resistor on the ISET pin
Set point voltage2.45 V to 2.55 V on the ISET pin, 2.50 V typical
Current set factor315 to 355 in the 50 mA to 1000 mA range, 372 typical in the 25 mA to 50 mA range
Regulated output4.2 V for the bq24010, bq24012, bq24013 and bq24014, 4.36 V on the bq24018 option
Pre-charge threshold2.80 V to 3.10 V on the BAT pin, 2.95 V typical
Short circuit threshold1.4 V to 1.8 V on the BAT pin, with a 225 mA to 280 mA trickle
Reverse leakage500 nA maximum on the BAT pin, which is what stops the cell draining back into the charger
Supply current3.5 mA to 5 mA charging, 5 microamps in sleep mode
TemperatureJunction range 0 C to 125 C for the published electrical limits

Body and ordering data

Body in this code10-pin MLP, the DRC outline, 3.00 mm by 3.00 mm
Pins in useIN, OUT, BAT, VCC, ISET, VSS plus the status, enable and sense pins of the chosen member
Thermal pathDie attach pad, soldered to copper with vias; the linear pass FET dissipates the input to battery difference
CarrierTape and reel, count per reel read from the vendor addendum row
DocumentSLUS530K, revised January 2014

Reading the code before you buy it

The five family members share a body and a pinout but not a pin function list, so an order code change inside the family is not always a drop in. Moving from a member without a temperature sense input to one with it puts a thermistor bias on a pin that was previously unused, and moving between members with and without the timer enable changes what the host has to drive at start up. A second source check has to compare the pin function table, not the current rating.

The other trap is the 4.36 V option. A 4.36 V charger on a 4.2 V cell is an overcharge, and the two options are the same body with the same pin names. Our drop in replacement check page covers the sequence we run before we let a substitute onto a board.

Dissipation is the last decision. A linear charger at 1 A from a 5 V adapter into a 3.7 V cell burns about 1.3 W in the pass FET, which a 3 mm square body can only carry with a solid copper pour and vias under the pad. At 500 mA the same board runs cool. The current setting is therefore a thermal decision as much as a charging time decision.

Where it fits in a build

Handheld instruments, medical monitors, handheld terminals, wireless headsets, cameras and any single-cell product that charges from a 5 V source fit this part. It also suits products that must charge from an unregulated adapter, because the family is specified to work from both regulated and unregulated supplies, and the input has its own undervoltage behaviour rather than needing an external supervisor.

Where a product needs the system to run while the battery is flat, this family is the wrong choice and a power path part is the right one: the bqTINY chargers put the system on the battery node, so a deeply discharged cell holds the system down until the conditioning phase ends. Our power management cross reference page sets out the difference between a charger and a charger with power path in the terms a buyer checks on a BOM.

Questions we get on this code

Can the charge current be changed after assembly? Yes, within the range the ISET resistor sets. The pin voltage is regulated to 2.50 V and the current follows the resistor, so a board with a resistor value change gives a different current. The pin can also be read as a current monitor during the constant voltage phase, which lets a host estimate the taper without a sense resistor.

What happens with no battery fitted? The charger sees the BAT pin rise and terminates on the timer or on the minimum current path depending on the member. On the versions with battery insertion detection the status outputs show the difference, which is why those versions are the ones used on products that ship with the pack removable.

Is a thermistor required? Not on the members without a temperature sense pin. On the members with it, an unconnected pin reads as a fault condition, so the pin has to be tied or populated. That is a line on the assembly drawing that is easy to lose between two members of the same family.

How do I know which reel count I will get? The count is in the vendor addendum row for the exact order code, and it changes between reel sizes of the same circuit. We confirm the row before quoting rather than reading a count from a distributor listing.