Contact Us

TPS65235RUKR

Brand: Texas Instruments
Texas Instruments TPS65235RUKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65235RUKR — Power Management & Signal Chain | Superb Automation

TPS65235RUKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65235RUKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65235RUKR: LNB voltage regulator with I2C and a 22 kHz tone generator

TPS65235RUKR is a satellite LNB supply that produces the 13 V to 18 V polarisation voltage and superimposes the 22 kHz tone in one package in a WQFN (RUK) body of 20 pins. It combines a boost converter and a low drop linear stage to make 13 V to 18 V from a 5 V or 12 V set top box rail, adds a 22 kHz tone for band switching, and is controlled over I2C with DiSEqC 1.x and 2.x signalling.

Order code and package

Ordering stringTPS65235RUKR, RUK package, 3 mm by 3 mm 20-lead WQFN, tape and reel
Package20-lead WQFN, 3.00 mm by 3.00 mm
FunctionLNB supply with I2C control, DiSEqC tone generation and diagnostics
Rails supported5 V, 12 V and 15 V input rails
Tone optionsInternal 22 kHz generator, or external 22 kHz and 44 kHz input
ControlI2C, and a dedicated enable pin for a system without a bus

Electrical parameters that decide the application

Output voltage13 V to 18 V, with a programmable transition time
Output current limitUp to 1000 mA, set by an external resistor
Boost switch140 milliohm internal FET, 1 MHz or 500 kHz selectable
Linear stageLow drop output with a push-pull stage, 0.8 V dropout
Tone amplitude650 mV to 750 mV, selectable in the 22 kHz generator
DiagnosticsOutput voltage level, tone input and output, current level, cable connection
ProtectionShort circuit dynamic protection, thermal protection

Points to check before this part goes on a BOM

The two stage arrangement is what keeps the heat out of the set top box. A linear regulator alone dropping 18 V down from a 20 V rail at 500 mA would dissipate watts, so the boost stage only lifts the rail to what the linear stage needs, and the linear stage then filters the switching ripple. The 0.8 V dropout figure is the budget the boost loop has to respect: at 18 V out and 500 mA, 0.4 W stays in the linear pass element and the rest of the conversion happens in the 140 milliohm switch.

The 1000 mA current limit is set by an external resistor, which means the same board can supply a single LNB or a multiswitch with different resistors. The limit also scales the boost switch peak current, so the inductor has to be chosen for the highest setting the board will ever use, not for the shipping configuration. A board built for 300 mA and later re-strapped for 900 mA will saturate its inductor before the new limit is reached.

The 22 kHz tone has to survive the linear stage, which is why the output stage is push-pull rather than a simple emitter follower. A single ended pass element can only source current, so the tone would be clipped at zero load, and the specification calls out that the tone is generated even with no load. A receiver that measures tone amplitude at the dish sees 650 mV to 750 mV, and the tolerance on that figure is set by the register selection rather than by the supply.

DiSEqC compatibility is a protocol promise, not a voltage promise. The part passes the tone and the modulation through, and the host has to produce the correct message timing for the switch or the multiswitch to respond. The diagnostics registers report what left the device, so a system that fails to switch can be separated into a supply problem and a protocol problem by reading the tone input and output status before changing any component.

The transition time between 13 V and 18 V is programmable, and that matters because a fast step looks like a fault to some LNBs and a slow step confuses the DiSEqC decoder. The data sheet allows the ramp to be set from the register, and the usual value is the one that keeps the current through the cable within the limit while the cable capacitance charges. A long cable is several nanofarads, so the inrush at a fast step is what trips the short circuit protection on a healthy installation.

I2C access with the enable pin low is the feature that makes production test practical. The registers can be read and written without turning the output on, so a fixture can verify the device, the bus and the diagnostics before any current flows into the cable. That also means a board that appears dead because the enable pin is held low can still be interrogated, which removes one of the usual blind spots in a satellite receiver repair.

Where this order code fits

It is the LNB supply in satellite set top boxes, integrated satellite televisions, PC satellite cards and multiswitch installations, where one cable carries both the DC polarisation voltage and the band switching tone. Teams comparing it with a neighbouring part start from our RF Component Sourcing page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it need an external tone source? No. There is an internal 22 kHz generator, and the external input is there for a host that wants to produce its own tone or a 44 kHz signal.

What sets the output voltage? The I2C registers, so 13 V and 18 V are selected by command rather than by a resistor, and the same board can serve both polarisations.

Is the current limit fixed? No. It is set by one external resistor up to 1000 mA, and the boost peak current limit follows it, so a change in the resistor changes two limits at once.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.