AD7656YSTZ-1
Product Specifications
AD7656YSTZ-1
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7656YSTZ-1 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD7656YSTZ-1: Six Channels Sampling at Once, 140 mW, and a 24 MHz Serial Clock
The AD7656YSTZ-1 is a six channel 16-bit successive approximation converter with all six channels sampling simultaneously at 250 kSPS, true bipolar inputs on both pins, pin or software selectable ranges of plus or minus 10 V and plus or minus 5 V, an on-chip 2.5 V reference with buffers, and parallel, serial and daisy chain interface modes in a 64-lead LQFP. It dissipates 140 mW at 250 kSPS from 5 V supplies, gives 86.5 dB of signal to noise ratio at a 50 kHz input, and drops to 100 uW maximum in standby. The -1 suffix is the variant with reduced decoupling requirements, and the vendor points new work at the AD7656A, which is pin compatible and improves supply rejection.
Simultaneous sampling is the reason to pay for six converters in one package
Six channels that sample on the same edge preserve the phase relationship between them, which is what a three phase power monitor or a multi-axis positioning system needs. A multiplexed converter with one sample and hold and six inputs samples the channels at six different times, and the resulting phase error is a function of the channel's frequency and the scan rate: at 50 Hz with a 250 kSPS scan, the 4 us between channels is 0.07 degrees, and at 1 kHz it is 1.4 degrees. Neither is fatal for a slow measurement and both are errors that have to be corrected if the measurement is a power calculation or a resolver angle.
The bipolar input is the second reason. Plus or minus 10 V with a 2.5 V reference is the plus or minus 4 times reference range, and it accepts a signal that swings below ground without a level shifting amplifier. An industrial sensor with a plus or minus 10 V output connects through a resistor and a capacitor rather than through an op amp and a reference, which saves the offset and drift of that amplifier from the error budget. The input impedance in that range is high enough that a 10 kohm source does not load it.
| Channels | Six, simultaneous sampling on one conversion start |
| Resolution | 16 bits, 14 and 12 bit members in the same family |
| Throughput | 250 kSPS per channel, 1.5 MSPS aggregate |
| Input range | Plus or minus 10 V or plus or minus 5 V, pin or software selectable |
| Reference | On-chip 2.5 V with buffers, plus or minus 4 times reference gives 10 V |
| Signal to noise ratio | 86.5 dB at 50 kHz, 14.08 effective bits |
| Power | 140 mW at 250 kSPS, 23.3 mW per channel |
| Standby | 100 uW maximum |
| Interfaces | Parallel, serial and daisy chain |
| Package | 64-lead LQFP |
The serial interface needs 24 MHz to keep up
Six channels of 16 bits is 96 bits per conversion, and a 250 kSPS rate gives 4 us for the whole frame, so the serial clock has to run at 24 MHz before any overhead for the conversion time and the inter-frame gap is counted. A host with a 20 MHz SPI port cannot read all six channels at the full rate over the serial interface, and the choice is either the parallel interface or a lower rate with a longer frame. That arithmetic is done once at the start of a project, and a board that runs into it after the interface is fixed ends up with a converter that measures at 200 kSPS and a specification that says 250.
The three conversion start pins allow the three channel pairs to be sampled independently, which is how a system with two different groups at different rates uses one package. Each pair has its own track and hold and its own conversion, so a fast group can run at 250 kSPS while a slow group runs at a tenth of that, and the reference and the interface are shared. This is the feature that makes the part a system component rather than six converters in a package.
140 mW for six channels is 23.3 mW per channel, which is a low power figure for a 16-bit converter with a plus or minus 10 V input. It comes from the high voltage CMOS process, which puts the input divider and the sampling switch on the die and removes the external amplifier. The trade is the supply arrangement: the part needs 5 V for the analog section and the interface, so a 3.3 V only board needs a boost or a separate rail, and that rail has to be quiet because the reference and the input range both scale with it.
The -1 suffix and the reference part
The AD7656-1 is the variant with lower decoupling requirements, which in practice means the internal reference and the supply arrangement tolerate a less generous capacitor bank than the plain part. A board that was laid out for the plain AD7656 has the capacitors already, so fitting the -1 is a substitution in the safe direction; a board laid out for the -1 and fitted with the plain part may not have the decoupling the plain part expects. That asymmetry is worth knowing before a purchasing change is made in the other direction.
The vendor also states that the AD7656A is the recommended part for new work, pin compatible and with improved supply rejection. Supply rejection matters on this part because the input range is set by the reference, which is derived from the 5 V rail: a 1 percent change in the rail with the internal reference in use moves the full scale, and the error appears as a gain error in the measurement rather than as an offset that can be trimmed once.
Two questions buyers ask
Can the six channels be read at 250 kSPS each over SPI?
Only with a 24 MHz clock or faster and a host that can sustain it. Below that the frame is longer than the conversion period and the effective rate falls. The parallel interface exists for exactly this case, and a board that chose the serial interface to save pins pays for it in throughput.
Does the on-chip reference remove the need for an external one?
For most industrial measurements it does, and the reference is buffered and brought out so an external one can override it. An external reference is worth it when the measurement needs better drift than the internal one or when several converters have to share a reference, which is the case on a card with more than one of these packages.
Ordering and supply
The AD7656YSTZ-1 is the 64-lead LQFP, minus 1 decoupling variant, lead free code. Cross references fail on the input range and on the simultaneity rather than on the resolution, because six multiplexed channels in the same package are not the same measurement as six simultaneous ones. A replacement also has to keep the plus or minus 10 V range if the sensor connects directly, since a plus or minus 5 V part needs a front end amplifier and the error budget for it.
We hold and source this family for production quantities and for repair lots. Start from the family page for analog mixed signal ICs, check a proposed alternative against the ADC and DAC cross reference, and for a power monitor or a protection relay the qualification route in medical device components shows the parts and approvals sequence such an instrument is checked against.
Request Quote — In Stock, 100% New & Original, Full Warranty