Contact Us

AD8626ARMZ-REEL

Brand: Analog Devices
Analog Devices AD8626ARMZ-REEL is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8626ARMZ-REEL — Analog & Mixed-Signal ICs | Superb Automation

AD8626ARMZ-REEL

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8626ARMZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8626ARMZ-REEL: One Picoamp of Bias, Five Volts Minimum, and the Supply Floor That Rules Out 3.3 V

The AD8626ARMZ-REEL is the dual member of the AD862x precision JFET input amplifier family, in an 8-lead MSOP. Input bias current is 1 pA maximum, offset voltage is 500 uV maximum, bandwidth is 5 MHz, supply current is 630 uA per amplifier typical, and the output is rail to rail and stable with capacitive loads above 500 pF. It runs from a single supply of 5 V to 26 V, or a dual supply of plus and minus 2.5 V to plus and minus 13 V, has no phase reversal, and is specified from minus 40 C to 85 C.

The 1 pA of bias current is the reason to select it: at 1 GOhm of source resistance that is 1 mV of offset, and at 10 MOhm it is 10 uV, which is a fiftieth of the amplifier's own offset. A bipolar input amplifier with 10 nA would produce 10 mV at the same 1 GOhm, a thousand times worse. The family also has a 5 MHz bandwidth and a 630 uA supply, so it is not a micropower part, it is a precision part that happens to be economical with current.

The five volt minimum is not a recommendation

The single supply range starts at 5 V, so a 3.3 V rail is outside the specification whatever the quiescent current suggests. That single line removes the part from most modern logic boards and puts it in 5 V, 12 V and 24 V industrial systems, which is where high impedance sensors still live. A board that needs 1 pA of bias on a 3.3 V rail has to use a CMOS input amplifier instead, and CMOS input amplifiers bring their own trade in noise and in input capacitance.

The 26 V maximum and the 630 uA per amplifier give a dissipation figure worth stating: at 26 V the part burns 16.4 mW per amplifier, or 32.8 mW for the pair, in an 8-lead MSOP. That is acceptable and it is not negligible in a sealed enclosure. At 5 V the same pair burns 6.3 mW, so the supply choice is also a thermal choice for a high impedance front end that may sit in a small housing.

Input bias current1 pA maximum, 1 mV into 1 GOhm
Offset voltage500 uV maximum
Bandwidth5 MHz, 500 kHz at a gain of 10
Supply current630 uA per amplifier typical, 16.4 mW at 26 V
Supply range5 V to 26 V single, plus and minus 2.5 V to plus and minus 13 V dual
OutputRail to rail, stable with 500 pF, no phase reversal
Input rangeSwings nearly rail to rail at the input
TemperatureMinus 40 C to 85 C, the extended industrial range
Package8-lead MSOP for the dual, SC70 for the single

Bias current and offset voltage cross over at about 500 MOhm

The point where 1 pA contributes the same voltage as the 500 uV offset is 500 MOhm. Below that the offset is the larger error, and above it the bias current takes over: at 1 GOhm the bias contributes 1 mV, twice the offset, and at 10 GOhm it contributes 10 mV, twenty times. So the 1 pA specification only pays at source impedances above a few hundred megohms, which is the photodiode, the electrometer and the pH electrode territory. At 10 MOhm the part is chosen for its 5 MHz and rail to rail output, not for its bias current.

Input capacitance is the other term that matters at those impedances, and the data sheet's 500 pF load stability is about the output, not the input. A 1 GOhm source with 5 pF of input capacitance and stray board capacitance forms a pole at a few tens of kilohertz, and with a 5 MHz amplifier the phase margin at that pole is thin. The usual answer is a feedback capacitor across the feedback resistor, which compensates the pole and costs bandwidth that the application was not using.

Two questions buyers ask

Can it be used as a photodiode transimpedance amplifier?
Yes, that is one of the named applications. The 1 pA bias keeps the DC error low, the 5 MHz bandwidth supports a fast photodiode, and the rail to rail output gives range on a 5 V supply. What has to be checked is the input capacitance and the feedback capacitor, because the transimpedance stage's stability depends on the diode capacitance and the resistor value rather than on the amplifier alone.

Is the quad version pin compatible?
The AD8625 is the quad and it is a different package with a different pinout, so no. Within the family the AD8627 single is offered in SC70 and SOIC, the AD8626 dual is in MSOP, and the AD8625 quad is larger again. A board that needs a fourth channel changes package, which is a board change rather than a substitution.

Ordering and supply

The ARMZ suffix is the 8-lead MSOP, lead free, in tape and reel. Substitution traps are the supply floor and the input bias current. A CMOS part with the same package and a 2.7 V minimum is not equivalent at 1 GOhm because its bias current is specified at 25 C only and rises steeply with temperature, and a bipolar part with the same 5 MHz has nanoamps of bias that swamp the source.

We hold and source this family for production and for repair. Start from the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and where a substitute has to be proven on a built board, work through how to verify a drop in replacement so the supply floor and the bias specification are checked before the first measurement.

Request Quote — In Stock, 100% New & Original, Full Warranty