ADUM3151BRSZ-RL7
Product Specifications
ADUM3151BRSZ-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADUM3151BRSZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADuM3151BRSZ-RL7: Seven Channels for SPI, 14 ns of Delay, and 3.75 kV of Barrier
The ADuM3151BRSZ-RL7 is a seven channel digital isolator built for isolated serial peripheral interfaces: four high speed channels for clock, master out, master in and chip select, plus three low speed channels with 2 in and 1 out directionality, in a 20-lead SSOP with 5.1 mm of creepage. The SPI channels support clock rates up to 17 MHz with 14 ns of propagation delay and 1 ns of jitter, the three auxiliary channels run at 250 kbps with up to 2.5 us of jitter, the barrier is rated 3750 V RMS for one minute under UL 1577 and 565 V peak of working voltage under VDE 0884-10, and the part operates to 125 C with more than 25 kV per microsecond of common mode transient immunity.
The timing budget of an isolated SPI link
At 17 MHz one bit is 58.8 ns, and 14 ns of propagation delay is 24 percent of a bit. A read transaction passes through the barrier twice, once for the clock and command going out and once for the data coming back, so the round trip is 28 ns and leaves 30.8 ns of the bit period for the slave's own access time and the cable or trace delay. A slave that needs 40 ns to put data on the bus cannot run at 17 MHz through this barrier, and the maximum clock rate for that slave is set by its own timing rather than by the isolator's rating.
The 1 ns of channel to channel jitter is what preserves the setup and hold relationship between the clock and the data channels. An isolator with 14 ns of delay and 5 ns of channel matching would put the clock and the data 5 ns apart at the far side, which at 58.8 ns per bit is 8.5 percent of a bit and enough to break a link that was timed at the near side. Matching is the specification that matters in a parallel bus and delay is the one that matters in a round trip, and both are in the same table.
| Channels | Seven: four SPI at up to 17 MHz, three auxiliary at 250 kbps |
| Auxiliary directionality | 2 in, 1 out on this code, other combinations in the family |
| Propagation delay | 14 ns on the SPI channels, 1 ns jitter |
| Bit period at 17 MHz | 58.8 ns, so a round trip is 28 ns |
| Auxiliary jitter | Up to 2.5 us at a 4 us bit period |
| Isolation | 3750 V RMS for one minute, 565 V peak working voltage |
| Creepage | 5.1 mm in the 20-lead SSOP |
| Transient immunity | More than 25 kV per us |
| Temperature | 125 C operation |
| Approvals | UL 1577, CSA 5A, VDE 0884-10 |
What the auxiliary channels are for, and what 2.5 us of jitter rules out
The three slow channels carry the signals that do not need speed: an interrupt from the isolated side, a reset going the other way, a status line, a converter's data ready flag. They are sampled and serialised at 250 kbps, which gives a 4 us bit period and up to 2.5 us of jitter, and that jitter is 62 percent of a bit period. A signal that is a level is unaffected, a signal that is a pulse is stretched or shortened by up to that amount, and a protocol that measures pulse width across the barrier is not served by these channels.
The directionality of the auxiliary channels is what distinguishes the three parts in the family. This code has two channels in one direction and one in the other, which suits a converter that raises an interrupt and a controller that sends a reset. A system where the isolated side has more to say than to hear needs one of the other two codes, and the difference is a copper change rather than a register setting.
The isolation ratings are two numbers for two purposes. The 3750 V RMS is a one minute withstand test, which is what a safety approval asks for, and the 565 V peak working voltage is what the barrier can hold continuously. A 600 V bus exceeds the working voltage even though a one minute test would pass, and the gap between the two figures is about 6.6 times in RMS terms, so reading the withstand number as the operating limit is the mistake that gets a product through the lab and into the field with a barrier that is degrading.
Isolated SPI in a real instrument
The application the part is built for is a programmable logic controller or a sensor interface where the measurement side is isolated from the control side, and the interface between them is SPI because that is what the converter on the isolated side speaks. Putting the isolator on the SPI bus rather than on a parallel bus keeps the pin count down, and keeping the four SPI signals on dedicated high speed channels is what allows the bus to run at the rate the converter supports rather than at a rate the isolator's slow channels allow.
The 20-lead SSOP with 5.1 mm of creepage is the package that a reinforced isolation requirement asks for, and the board's isolation slot has to be placed under the package rather than beside it. A part with the right rating in the wrong footprint leaves the creepage to the board, and the board's slot is only as good as the routing around it. The isolator's own supply pins sit on both sides of the barrier, so the isolated side needs its own supply, which on many boards is a small transformer driver and a regulator rather than a second converter.
Two questions buyers ask
Does it provide isolated power as well as isolated data?
No. The part isolates the signals and each side needs its own supply. A board that needs isolated power uses a separate transformer driver with a rectifier and a regulator, or one of the family members with an integrated power converter, which is a different order code with a different current budget.
Can the SPI clock run at 25 MHz through this part?
The SPI channels are specified to 17 MHz, and the limit is the propagation delay and matching rather than the barrier. Running above the specified rate gives a link that works on a bench and fails at temperature, because the timing margins are what the specification covers. A converter that needs 25 MHz needs a different isolation arrangement.
Ordering and supply
The ADuM3151BRSZ-RL7 is the 20-lead SSOP tape and reel code with two auxiliary channels in and one out. Cross references fail on the channel directionality and on the auxiliary jitter rather than on the isolation rating, because a part with the same barrier and a different split of directions needs a different board. A replacement also has to match the creepage the approval was granted against.
We hold and source this family for production quantities and for repair lots. Start from the family page for analog mixed signal ICs, check a proposed alternative against the pin to pin cross reference, and for a controller or a monitor that carries a patient connection the parts route in medical device components is where the barrier and the approvals are checked together.
Request Quote — In Stock, 100% New & Original, Full Warranty