AD5453YRMZ-REEL7
Product Specifications
AD5453YRMZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5453YRMZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD5453YRMZ-REEL7: A 14-Bit Multiplying DAC, 12 MHz of Bandwidth, and a Reference That Can Swing Past the Supply
The AD5453YRMZ-REEL7 is a 14-bit current output multiplying digital to analogue converter in an 8-lead MSOP that runs from 2.5 V to 5.5 V, updates at 2.7 MSPS, and takes a serial word at up to 50 MHz. Its distinguishing feature is the reference input: it accepts plus or minus 10 V even though the part itself runs from a single 2.5 V to 5.5 V supply, and the multiplying bandwidth is 12 MHz, so the reference can be an AC signal and the output is the product of that signal and the digital code. The output is a current, so an external amplifier converts it to a voltage using the on-chip feedback resistor, which tracks the internal resistors over temperature. Power-on reset with brownout detection holds the output at zero scale, the part is guaranteed monotonic over all codes, current consumption is under 0.4 uA typical, and the family is qualified for automotive applications.
The family covers 8, 10, 12 and 14 bits with pin compatible packages, which means a board can be laid out once and the resolution chosen at build. That is convenient and it is a sourcing trap, because the four order codes differ in one digit and the resolution is not visible on the package.
One LSB is 1.221 mV on a plus or minus 10 V reference
With a plus or minus 10 V reference the output span is 20 V and a 14-bit LSB is 1.221 mV. Four quadrant multiplication means the reference can be positive or negative and the code can be either, so the output covers plus and minus full scale; the amplifier that converts the current to a voltage has to be able to swing that far, and it is the amplifier rather than the converter that sets the output range and the settling. The 12 MHz multiplying bandwidth is the frequency at which the reference can change while the output still follows, and a 12 MHz sine has a period of 83 ns, well under the 370 ns update interval of the 2.7 MSPS rate.
The 50 MHz serial interface and the 2.7 MSPS update rate are not the same limit. A 16-bit word at 50 MHz takes 320 ns, so the interface can deliver a word faster than the converter can settle, and the update rate is the binding constraint. A system that needs faster updates needs a different part, and a system that needs a faster interface for a shared bus is already covered.
| Resolution | 14 bits, guaranteed monotonic |
| Output | Current output, four quadrant multiplication |
| Reference input | Plus or minus 10 V, independent of the 2.5 V to 5.5 V supply |
| Multiplying bandwidth | 12 MHz, 83 ns per cycle |
| Update rate | 2.7 MSPS, 370 ns per update |
| Interface | 3-wire serial to 50 MHz, double buffered |
| Supply current | Under 0.4 uA typical |
| Power-on state | Zero scale, with brownout detection |
| Family | 8, 10, 12 and 14 bit members pin compatible |
| Package | 8-lead MSOP, also TSOT and LFCSP for some members |
The reference can be an AC signal, and that is the point of a multiplying DAC
A multiplying converter is used where the output has to be a product: a programmable gain stage where the reference is the signal and the code is the gain, a digitally controlled attenuator, a waveform generator where the reference is a sine and the code modulates its amplitude, or a calibration path where one DAC trims another. In each case the accuracy of the product depends on the reference path's linearity and on the feedback resistor's tracking, which is why the resistor is on the die: a 100 ppm per degree C external resistor would add a gain drift the converter does not have.
The current output means the load is the summing junction of an external amplifier, and the amplifier's input bias current adds directly to the output current. An amplifier with 1 uA of bias against a 1 mA full scale current is 0.1 percent, which is 16 LSB at 14 bits, so the amplifier choice is part of the converter's accuracy. A CMOS input amplifier with picoamps of bias and enough bandwidth for the application is the usual answer, and its own offset appears at the output as a constant.
Two questions buyers ask
What linearity does the 14-bit member have?
The family feature list quotes integral nonlinearity at the 8-bit member, plus or minus 0.25 LSB, which is a property of the 8-bit part and cannot be read across to the 14-bit one. The linearity for this order code has to come from the 14-bit column of the data sheet, and a buyer who quotes the family headline in a specification is quoting the wrong device.
Can it be used as a simple voltage output DAC?
Only with an external amplifier. The part delivers a current and needs an I to V stage, which is the price of the multiplying architecture and the reason a board that just needs a setpoint should use a voltage output converter instead. Where the multiplication is needed the amplifier is already there, so the current output costs nothing extra.
Ordering and supply
The YRMZ suffix is the 8-lead MSOP, lead free, in tape and reel. Substitution traps are the resolution, the reference range and the output type. A voltage output part cannot be dropped into a current output socket, and a current output part with a 5 V maximum reference cannot take the plus or minus 10 V reference that the circuit provides.
We hold and source this family for production and for repair. Start from the analog mixed signal ICs family page, compare a candidate against the ADC and DAC cross reference, and where a substitute has to be proven on a built board, use the sequence in how to verify a drop in replacement so the resolution and the reference range are checked first.
Request Quote — In Stock, 100% New & Original, Full Warranty