Contact Us

TPS65130RGER

Brand: Texas Instruments
Texas Instruments TPS65130RGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65130RGER — Power Management & Signal Chain | Superb Automation

TPS65130RGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65130RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65130RGER: dual positive and negative output converter, 15 V and minus 15 V, 0.8 A switch, VQFN-24

TPS65130RGER is a dual output converter that makes one positive rail up to 15 V and one negative rail down to minus 15 V from a single 2.7 V to 5.5 V input in a VQFN body of 24 pins. The two outputs are independent, with separate enable pins and separate feedback dividers, so the positive and negative rails do not have to be symmetrical. The positive side is a boost converter and the negative side is an inverting buck boost, which is why the part can serve a split supply from a battery or from an existing 3.3 V or 5 V rail.

Order code and package

TPS65130RGERActive, VQFN-24, 3000 pieces on a large reel, NIPDAU finish, MSL-2-260C with a one year floor life, marking 5130
TPS65131RGERActive, the same body with the 2 A switch limit instead of 0.8 A
TPS65130RGETActive, 250 pieces on a small reel for prototypes
TPS65131RGERG4Obsolete in the addendum, so the Green variant of the 2 A part should not be specified for a new build
Temperature rangeminus 40 to 85 degrees on every row, which is narrower than most industrial converters around it

Electrical parameters that decide the application

Input voltage2.7 V to 5.5 V
Positive outputadjustable up to 15 V, switch current limit 0.8 A on this part number
Negative outputadjustable down to minus 15 V, inverter switch limit about 800 mA typical
Output currenttypically 200 mA to 500 mA combined, depending on the input to output ratio
Switching frequency1.25 MHz minimum, fixed frequency PWM with pulse skipping at light load
Quiescent current500 microamp typical, device on and no load
Shutdown current1 microamp typical
Efficiencyup to 89 per cent on the positive rail, 81 per cent on the negative rail, 85 per cent combined

Family variants and how they differ

TPS651300.8 A switch limit, suited to panel bias at a few hundred milliamp
TPS651312 A switch limit, for larger panels and for split supplies that need more current
ENP and ENNindependent enable pins, so the positive rail can come up before the negative one
CN and CP pinsflying capacitors for the inverting stage, tied to the switch node
Control outputdrives an external P channel FET to disconnect the battery completely

Points to check before this part goes on a BOM

The two rails are not symmetrical and should not be quoted as if they were. The positive side is a boost with a 0.8 A switch limit; the negative side is an inverting buck boost with its own limit. At 3.3 V in and plus or minus 12 V out, the current available on the negative rail is lower than on the positive one, and a panel that needs equal currents will run out of negative headroom first.

The 0.8 A switch is the whole story on this part number. TPS65131 carries the same silicon with a 2 A limit, and the two are pin compatible. During a shortage it is tempting to take whichever is on the shelf, but the inductor and the input capacitor were sized for one limit. A 2 A part in a 0.8 A circuit is fine; the reverse swap needs the magnetics checked against the current the load actually draws.

Separate enables are a sequencing tool, not a convenience. Most panels want the positive rail first, then the negative rail, and some want the opposite. With ENP and ENN driven from two GPIOs the order is under firmware control. Tying them together removes that control and can leave a panel latch up if the negative rail arrives before the logic supply.

Five hundred microamp quiescent is high for a battery product. It is the price of a dual controller running two loops with an internal reference. For a device that stays on all the time on a coin cell this part is the wrong choice; for a handheld that is switched on and off, the 1 microamp shutdown current is what matters and the rail should be disabled between uses.

The 85 degree limit is the trap in this order code. The addendum prints minus 40 to 85 for the RGE body. A panel bias supply inside a sealed enclosure can reach that ambient, and there is no margin left. Boards that must run hotter need a different family, not a different reel.

Loop compensation for the inverting stage lives outside the part. The negative converter needs its own compensation network tied to the CN pin, and the values depend on the flying capacitor and the load current. A board copied from a reference with a different panel will oscillate at light load if those parts are carried over without recalculation.

MSL-2 with one year floor life applies here. That is a real constraint for a 24 pin quad flat no lead body: after 168 hours out of the bag the reel needs a bake. A broker reel that has been open for months is a moisture risk that shows up as delamination after reflow, not on incoming inspection.

The control output is often left unconnected and should not be. It drives an external P channel FET that disconnects the battery when the converter is off. Without that FET the input rail stays connected through the inductor and the body diodes, and a device that is switched off still drains the cell. On a battery product this pin is part of the shutdown current budget, not an optional extra.

Efficiency numbers are quoted at specific ratios. The 89 per cent on the positive rail and the 81 per cent on the negative rail are typical at the ratios in the data sheet, not a promise across the range. At 5 V in and 15 V out the boost runs at a high duty cycle and the losses climb; at 3.3 V in and minus 15 V out the inverter carries more current than the load for the same output power.

What to confirm before this part goes on a purchase order

Confirm whether the board needs the 0.8 A or the 2 A switch before quoting, because the two strings share a footprint and a pinout but not a price or a stock position. State the required rail voltages and the current on each rail so the offer can be checked against the switch limit rather than against the family name.

For repair demand ask for the date code and the country of origin, and check that the reel label carries the 5130 marking. Because TPS65130 and TPS65131 look identical on the reel, the marking and the ordering string are the only way to tell them apart after the bag is open.

Where this order code fits

It makes the positive and negative rails for an LCD or AMOLED panel, and the split supply for a data acquisition front end or a differential amplifier, from one 3.3 V or 5 V input. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can it make plus and minus 15 V from a 3.3 V rail? It can make the voltages, but the current available falls as the ratio grows. From 3.3 V in, the positive rail at 15 V and the negative rail at minus 15 V leave very little current on the negative side because the inverter carries the full load current through its switch. The data sheet curves show the practical window.

What happens if the negative rail is loaded before the positive one? Nothing breaks, but the sequencing the panel expects is not met. Use the separate enable pins to bring the rails up in the order the panel data sheet asks for, and check the panel supply sequence table before tying the two enables together.

Is the 1.25 MHz minimum switching frequency fixed? The converter runs at a fixed frequency above 1.25 MHz and enters pulse skipping at light load. Pulse skipping changes the ripple spectrum, which matters when the negative rail feeds an analogue front end; a minimum load or a forced PWM mode through the mode pin keeps the spectrum clean.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.