Contact Us

AD825ARZ-REEL7

Brand: Analog Devices
Analog Devices AD825ARZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD825ARZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

AD825ARZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD825ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD825ARZ-REEL7: A JFET Input Amplifier with 41 MHz and 20 pA of Bias Current

What this part is

The AD825 is a junction field effect transistor input operational amplifier with 41 megahertz of bandwidth, 125 volts per microsecond of slew rate and 80 nanoseconds of settling, specified on both plus and minus 5 V and plus and minus 15 V supplies. Bias current is 20 picoamps with a current noise density of 10 femtoamps per root hertz, which is the combination that makes the part useful in front of a high impedance source: the offset the bias current develops across the source resistance stays small even when that resistance is large.

The input stage is built so that a signal reaching either rail does not cause phase reversal at the output, and the output delivers 50 milliamps minimum and is specified to drive unlimited capacitive load, which is unusual and is the reason the part appears as a cable driver and as a multiplexer buffer. Supply current is 6.5 milliamps. The body is an eight lead small outline. The vendor lists the part as a general purpose high speed amplifier, which understates it: the JFET input is the distinguishing feature, and the rest of the specification is there to make the input useful.

Published figures that matter to a buyer

Input stageJFET
Bandwidth41 MHz at minus 3 dB
Slew rate125 volts per microsecond
Settling time80 nanoseconds
Input bias current20 picoamps
Input current noise10 femtoamps per root hertz
Input voltage noise12 nanovolts per root hertz
Distortionminus 76 dB at 1 MHz
Output current50 milliamps minimum
Capacitive loadspecified for unlimited load
Suppliesplus and minus 5 V and plus and minus 15 V, both fully specified
Supply current6.5 milliamps
Body8 lead small outline

Where the headline numbers stop

Bias current of 20 picoamps develops 20 microvolts across 1 megohm and 200 microvolts across 10 megohms, so the JFET input is worth having above a few hundred kilohms and is irrelevant below ten. That is the honest way to read the part: on a 50 ohm source the 12 nanovolt voltage noise dominates and a bipolar amplifier would do the same job for less money, while on a 10 megohm photodiode or pH electrode the bias current is the only thing that matters.

Speed and amplitude have to be read together. A slew rate of 125 volts per microsecond gives 3.98 megahertz of full power bandwidth at a 10 volt peak to peak output and 1.99 megahertz at 20 volts peak to peak, so the 41 megahertz small signal figure belongs to small signals. Distortion of minus 76 dB at 1 megahertz is 12.3 effective bits, which sets the part in the 12 bit class for a signal at that frequency however good the converter behind it is.

The output stage is the other half of the story. Fifty milliamps into 100 ohm is 5 volts peak, into 50 ohm it is 2.5 volts peak, and at plus and minus 15 V the supply sets the ceiling before the current does. Six and a half milliamps of supply current at 30 volts total is 0.195 W, which is a warm eight lead body. The claim to drive unlimited capacitance is a stability statement about the internal compensation, not a promise that a 1 microfarad load settles in 80 nanoseconds, so the settling figure should be applied to the load the data sheet specifies.

Applications where it fits

  • Buffers for multiplexer outputs and sample and hold circuits, where a JFET input keeps the droop low.
  • High impedance sensor front ends: photodiodes, pH electrodes, piezo elements and electrometer stages.
  • Cable and capacitive load drivers in test equipment and video distribution.
  • Active filters and integrators that need a fast amplifier with a clean input.
  • Signal conditioning on plus and minus 15 V rails where a 5 V part would clip.

Two questions buyers ask

Can it drive a long cable directly? The output delivers 50 milliamps and is specified to drive unlimited capacitive load, which is what a cable looks like. What the specification does not promise is that the far end is terminated: a cable driven into an open end reflects, and the 80 nanosecond settling figure was measured into a defined load. A series resistor at the output is still the usual practice.

Is a bipolar amplifier with lower noise a substitute? Only if the source impedance is low. A bipolar part with 1 nanovolt of voltage noise but nanoamps of bias current develops more error across a 1 megohm source than the AD825 does with its 12 nanovolts. The substitution decision is a source impedance question first and a noise question second.

Sourcing notes and next step

AD825ARZ-REEL7 is the eight lead small outline in tape and reel, and the A grade is the only grade offered for this part, so the letter in the order code is not a quality selector here. The part has been catalogued for a long time, which means the data sheet is stable and the distribution channel is deep, and it also means a substitute proposed by a broker should be compared against the vendor document rather than against a summary. The analog and mixed signal IC family page lists the amplifier line, the amplifier cross reference page sets out the parameters that matter for a JFET input part, and the drop in verification page covers the tests before a substitute goes into a build.

Request Quote — In Stock, 100% New & Original, Full Warranty