AD8502ARJZ-REEL7
Product Specifications
AD8502ARJZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8502ARJZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8502ARJZ-REEL7: Two Amplifiers That Run on One Microamp
What this part is
The AD8502 is a dual CMOS operational amplifier with a maximum supply current of 1 uA per amplifier, a maximum offset of 3 mV, and a typical input bias current of 1 pA. The inputs and outputs both swing rail to rail, so the part works from a single 1.8 V to 5.5 V supply, or from a split supply of plus or minus 0.9 V to plus or minus 2.75 V, without losing the ends of the range. It is unity gain stable and does not phase reverse when an input is driven beyond a rail.
This is a part for the corner of a battery instrument where the signal is slow and the current budget is the constraint: bedside monitors, pulse monitors, glucose meters, smoke detectors and vibration monitors all need an amplifier that is awake all the time without flattening the cell. The ARJZ suffix is the 8 lead SOT-23 on a 7 inch reel.
Published figures that matter to a buyer
| Channels | 2 |
| Supply current | 1 uA maximum per amplifier |
| Offset voltage | 3 mV maximum |
| Input bias current | 1 pA typical |
| Input and output range | rail to rail on both |
| Supply range | 1.8 V to 5.5 V single, plus or minus 0.9 V to plus or minus 2.75 V split |
| Phase reversal | none |
| Stability | unity gain stable |
| Temperature range | minus 40 to plus 85 degrees C, and to plus 125 degrees C on the extended grade |
| Package | 8 lead SOT-23, tape and reel |
Where the headline numbers stop
One microamp per amplifier at 3 V is 3 uW, and two amplifiers running continuously for a year draw 17.5 mAh. That is the number to compare with the self discharge of the cell and with the quiescent current of whatever sits downstream, because a 17.5 mAh annual budget is smaller than the leakage of many battery supervisors. The supply current is a maximum rather than a typical figure, which is the right way to budget a battery life calculation.
The 3 mV offset is what limits the gain. At a gain of 100 the offset appears as 300 mV at the output, and at a gain of 1000 it is 3 V, which is the whole rail. A micropower amplifier with this offset is therefore a buffer or a low gain stage, and a high gain stage on a small signal needs a chopper stabilised part instead. The 1 pA bias current is what keeps the part usable with a high impedance source: into 10 MOhm it produces 10 uV, which is 0.3 percent of the offset.
Rail to rail operation matters most in the middle of a small supply range. On a 1.8 V rail a part that cannot swing within 200 mV of either end loses 22 percent of the span, and on a 5.5 V rail the same 200 mV is 7 percent. The AD8502 is specified to swing to both rails, so the useful dynamic range is the whole supply rather than the middle of it, and a single cell instrument gets the full 1.8 V of output swing from a 1.8 V cell rather than the 1.4 V that a conventional input stage would leave.
Applications where it fits
- Portable medical monitors that must run for months on a coin cell or a small lithium cell.
- Remote sensor nodes where the amplifier is powered continuously and the radio is not.
- Low power active filters and threshold detectors in battery equipment.
- Current sensing in energy harvesting circuits, where the sense amplifier cannot cost more than the harvested power.
Two questions buyers ask
How fast is it? The vendor page for this part does not publish a gain bandwidth figure in its headline list, and a 1 uA amplifier is a slow part by construction. A signal chain built around it has to be specified from the full data sheet bandwidth rather than from an assumption, and any stage that needs more than a few kilohertz should be checked against the measured curve before the board is committed.
Does the rail to rail input work at both ends? The vendor states rail to rail input and output and no phase reversal. Rail to rail input stages are often implemented with two input pairs, one of which takes over near the positive rail, and the crossover can show as a small offset step; for a DC instrument that is worth measuring rather than assuming.
Sourcing notes and next step
The AD8502ARJZ-REEL7 is the 8 lead SOT-23 on a 7 inch reel, and the quad version in a 14 lead TSSOP is the AD8504 for boards that need more channels in the same current budget. The analog and mixed signal IC family page lists the amplifier line, the amplifier cross reference page covers the substitution route across micropower parts, and the medical device components page sets out the traceability route for patient monitoring equipment.
Request Quote — In Stock, 100% New & Original, Full Warranty