Contact Us

TPS62A02PDDCR

Brand: Texas Instruments
Texas Instruments TPS62A02PDDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62A02PDDCR — Power Management & Signal Chain | Superb Automation

TPS62A02PDDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62A02PDDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62A02PDDCR 2 A buck with power save operation

The TPS62A02PDDCR is the power save member of the TPS62A0x 2 A line in the DDC SOT-23 body. It runs from 2.5 V to 5.5 V, switches at 2.4 MHz at medium and heavy load, and enters power save at light load, where the frequency drops and the quiescent current falls below 23 microamp. The output is set by a divider on the FB pin from 0.6 V up to the input voltage, and the 100 per cent duty mode carries the rail to the end of a battery discharge.

The electrical detail is the family detail: 100 milliohm high side and 67 milliohm low side on the 2 A body, a 600 mV reference with a 591 mV to 609 mV window over temperature, 0.01 microamp of shutdown current and an undervoltage lockout between 2.3 V and 2.5 V rising. The difference between this part and the A member is the behaviour at light load, and that difference is the reason both exist: a rail that feeds a radio takes forced PWM, a rail that feeds a sleeping microcontroller takes power save.

Power save is not a burst mode with an uncontrolled ripple. The part reduces its switching frequency and holds the output in regulation with a low quiescent current, so a 3.3 V rail that supplies a real time clock and a memory retention domain keeps its voltage while the input current falls into the microamp range. For a product that runs on a coin cell or a small lithium cell, that mode is the difference between a year and a month.

Key parameters from the SLUSEG9E document

Input range2.5 V to 5.5 V
Output range0.6 V to the input voltage through the FB divider
Output current2 A on this member
Switching frequency2.4 MHz at medium and heavy load, reduced in power save at light load
Switch resistance100 milliohm high side and 67 milliohm low side on the 2 A body
Feedback voltage600 mV nominal, 591 mV to 609 mV over the full temperature range
Quiescent currentBelow 23 microamp in the non switching state
Shutdown current0.01 microamp typical
UVLO2.3 V to 2.5 V rising
Operation modePower save with automatic PWM to PFM transition at light load
Thermal noteContinuous 2 A below 3.3 V input or above 85 degrees ambient can reach thermal shutdown
PackageDDC SOT-23 body with six pins

What power save does to a measurement

A converter that skips cycles produces a low frequency component in its output ripple, and that component sits in the band where an analogue front end or an audio path is most sensitive. On a rail that feeds a sensor bridge, the burst appears as a periodic offset in the reading, and it is often blamed on the sensor rather than on the supply. The remedy is either a forced PWM member or enough output capacitance and a small series ferrite to push the burst out of the band.

The quiescent current figure matters for the same reason it does in the nanoamp parts, only less so. At 23 microamp the converter is not the largest load in a sleeping product, but it is not negligible either, and the difference between power save and forced PWM at light load is three orders of magnitude in input current. A product that spends most of its life asleep takes the power save member without a second thought.

The 100 per cent duty mode is the same on both members. At 2 A the two switches in series drop about 330 millivolt, so a 3.3 V rail holds until the input falls to about 3.6 V and then follows the battery down. A customer who asks how the product behaves at the end of discharge is asking about this mode rather than about the switching behaviour.

Where this part fits

Battery powered instruments, wireless sensor nodes, portable medical devices and any board that needs 2 A in a leaded package with a low standby current. Our cross reference notes are at power management cross reference and the substitution check is at how to verify a drop in replacement.

What to check before a purchase order

Check the mode letter. The A members are forced PWM and this member is power save, and the two share a package and a pinout, so the reel label is the only way to tell them apart. A product that was characterised with one and built with the other will pass a functional test and may fail an emissions or a noise test.

Check the divider values and their tolerance. The 600 mV reference is low enough that a pair of 5 per cent resistors gives an output error of a few per cent, which on a 1.2 V rail is tens of millivolts. A 1 per cent pair costs almost nothing and removes the error term entirely. The receipt check is at incoming inspection plan.

Questions that come up on this part

Does the part hold regulation at no load, is a common question. It does, in power save, with the output held by the loop and the switching frequency reduced. The output ripple at no load is larger than at 2 A, which is the property to check against a load that is sensitive to ripple rather than to voltage.

The second question is whether the 2 A rating is available at 2.5 V input. The current limit allows it, but at 2.5 V in and 1.8 V out the duty cycle is high, the switches conduct for most of the period, and the loss at 167 milliohm in series is about 670 milliwatt. That is more than the SOT-23 body can remove at high ambient, so the usable current at the bottom of the input range is thermal rather than electrical.