DRV5033AJQDBZR
Product Specifications
DRV5033AJQDBZR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5033AJQDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5033AJQDBZR: an omnipolar switch that answers to either pole
The DRV5033AJQDBZR is a digital omnipolar Hall switch in the SOT-23 body, with a 6.9 mT operate point and a 3.5 mT release point. Omnipolar means the output responds to a north pole and a south pole alike, so the mechanical assembly does not have to guarantee which way the magnet was pressed in.
That single property removes a whole class of production faults. On a unipolar part a reversed magnet produces no output at all, and the fault shows up at end of line test as a dead sensor. On this part either pole operates the switch, which is why it appears in docking stations, door sensors and valve position indicators where the magnet orientation is set by a subcontractor.
The rest of the specification is the industrial Hall standard: 2.5 V to 38 V supply with no regulator, 30 mA open drain output, reverse supply protection to 22 V, 35 us power-on time and a temperature range of minus 40 C to plus 125 C.
Key data for the DRV5033AJQDBZR
| Output | Open drain, 30 mA sink, active low above the operate point |
| Operate point | 6.9 mT typical on the AJ option, within 10 percent over temperature |
| Release point | 3.5 mT typical, so 3.4 mT of hysteresis |
| Magnetic response | Omnipolar, a north pole and a south pole both operate the switch |
| Supply | 2.5 V to 38 V, no regulator, reverse protection to 22 V |
| Response time | 35 us power-on time with an output pulse to mark validity |
| Temperature | Minus 40 C to plus 125 C on the Q grade |
Body, packing and marking data
| Body | SOT-23, three pins, DBZ outline |
| Packing | 3000 pieces on a large reel on the R suffix, 250 on the T suffix |
| Finish | Nickel palladium gold and tin, moisture level 1 at 260 C on the A revision row |
| Marking | QLAJ and 1J72 on the body, which is how the AJ die is identified on a mixed reel |
How the AJ option sits in the family
The DRV5033 comes in two thresholds. FA is 3.5 mT with a 2 mT release point and AJ is 6.9 mT with a 3.5 mT release point, so AJ needs roughly twice the field to operate and holds on to a stronger field before it releases. Everything else, supply range, output stage, protection and temperature, is common to both.
The code carries the body and the packing after the sensitivity. QDBZR is the Q grade, SOT-23 body and reel, and QLPG is the same die in TO-92 with bulk or ammo packing after it. The automotive version of the family is published under its own part number, so a Q1 suffix on this string would need confirming rather than assuming.
One addendum detail is worth knowing before a reorder: the DMR body is not offered for AJ on this family, only DBZ and LPG, so a board that was migrated to the small X2SON body cannot be filled with this threshold.
Where an omnipolar switch earns its place
Docking detection, door and lid position, valve positioning and pulse counting on a rotating target are the vendor's list. In each of them the sensor is a presence detector rather than a direction detector, and the mechanical tolerance on magnet orientation is the reason the omnipolar version is chosen over the cheaper unipolar part.
Where the same magnet has to trigger two sensors on one board, the pin to pin cross reference page covers the threshold and hysteresis differences that make one part chatter where another does not, and the supplier quality audit page sets out what to ask a new source for on a magnetic part.
Questions we get on this code
If either pole works, why does the data sheet still talk about a positive and negative field? Because the internal comparator sees the magnitude with the sign folded out, but the thresholds are still specified against a field direction for test purposes. In practice the assembly drawing does not have to control the pole, and that is the whole point of the option.
The other question is whether an omnipolar part can be used as a direction sensor. It cannot: the output looks the same whether the field is north or south, so the part reports presence only. A latch is the part for direction, because it remembers which pole arrived last.
The last thing to check is the pull up value against the load. The output sinks 30 mA, but the current that flows is set by the pull up resistor and the supply, not by the sensor. On a 24 V rail a 1 k pull up asks for 24 mA whenever the output is low, which is inside the sink limit but well above what a small signal diode in the receiving circuit may want to see.