Contact Us

ISOW7721DFMR

Brand: Texas Instruments
Texas Instruments ISOW7721DFMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISOW7721DFMR — Power Management & Signal Chain | Superb Automation

ISOW7721DFMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISOW7721DFMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISOW7721DFMR: two isolated channels and their supply in one body

The ISOW7721DFMR is a two channel digital isolator with an integrated DC-DC converter in a 20 pin wide body. One channel runs forward and one runs back, so the part covers a full duplex pair, and the converter generates the isolated rail that the far side needs. A board that used to carry an isolator, a transformer driver, a transformer and a rectifier now carries one package and a few capacitors.

The converter switches at 25 MHz, which is deliberately low for an integrated supply, and the vendor states that emissions meet CISPR 32 and EN 55032 class B with more than 5 dB of margin on a two layer board. The package has provisions for ferrite beads where a tighter limit applies or where the board routing is less forgiving than the reference. Data rate on the isolated channels reaches 100 Mbps, which is fast enough to carry a serial link or an encoder interface.

Isolation is 5000 VRMS for one minute under UL 1577 with a repetitive peak rating of 7071 VPK and a working voltage of 1000 VRMS. The part is rated for minus 40 C to plus 125 C, and the isolated supply makes it usable on a board where the field side has no other power source.

Key data for the ISOW7721DFMR

FunctionTwo digital isolation channels plus an integrated isolated DC-DC converter
DirectionOne channel forward and one reverse, the F variant with a low default is also offered
Data rate100 Mbps on the isolated channels
Isolation5000 VRMS for 60 s per UL 1577, 7071 VPK repetitive peak, 1000 VRMS working voltage
Converter25 MHz switching frequency, chosen for low noise rather than for a small transformer
EmissionsStated to meet CISPR 32 and EN 55032 class B with more than 5 dB of margin on a two layer board
Supply currentAbout 4 mA per channel at 1 Mbps, rising past 11 mA at 100 Mbps with both channels switching

Body, packing and marking data

BodySOIC DFM, 20 pins, the wide isolated body that carries the converter
Packing850 pieces on a large reel
FinishNIPDAU, moisture level 3 with a 168 hour floor life, 260 C peak
MarkingISOW7721 printed on the body
TemperatureMinus 40 C to plus 125 C

Power budget is the first calculation

The converter has a finite output power, and it is shared between the isolated side of the isolator and whatever else the field side draws. A termination resistor, a sensor and the quiescent current of a transceiver all come out of the same budget, and the budget falls as the ambient temperature rises. Start from the worst case load at 125 C rather than from the typical load at 25 C, and remember that the converter recycling into a shorted field side will shut down rather than hold its output.

The second calculation is the switching noise path. The converter runs at 25 MHz, and its harmonics can land on a sensitive receive band or on an ADC sampling clock. The ferrite bead provisions in the package exist for that reason, and a two layer board with a long return path will not meet the stated margin even if the circuit is copied exactly. Measure the emissions on the first article rather than trusting the reference.

Where two channels with their own supply are used

Isolated serial ports, field sensor interfaces and medical monitors with a patient connected module all use this shape. The field side needs a few milliamps, the barrier has to hold 5000 VRMS, and there is no room for a transformer. One package solves all three at once, and the only external decision left is how much current the field side really needs.

For a product heading into a regulated medical submission, our medical device component sourcing page covers the working voltage question, and the pin to pin cross reference page is where a replacement check starts when the supply arrangement is changing.

Questions we get on this code

Buyers ask whether the isolated supply can drive a second device. It can, up to the current limit and the thermal budget, but every milliamp taken by another load reduces the margin on the isolator itself. Add the loads first and size the part afterwards rather than the other way round, and check the inrush of any load that switches on after the converter has started.

The second question is about the reel count. This body ships 850 pieces on a 330 mm reel, not the 2000 that a 16 pin part ships, so a production order quoted in reels is a different piece count. Convert to pieces before the price is agreed, and check the carrier width against the feeder on the line.