DRV2700RGPR
Product Specifications
DRV2700RGPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV2700RGPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV2700RGPR: one package for a 100 V piezo driver, boost converter included
The DRV2700RGPR drives a piezoelectric actuator from a 3.3 V to 5.5 V rail and generates the high voltage itself. The package contains a 105 V boost switch, the boost diode and a fully differential amplifier, so the only external power components are an inductor, a handful of capacitors and two feedback resistors that set the boost level. In boost plus amplifier configuration the output reaches plus and minus 100 V, and with a flyback transformer in place of the inductor the same part reaches 1 kV.
The amplifier has four gain settings selected by two pins: 28.8 dB, 34.8 dB, 38.4 dB and 40.7 dB. Those are not arbitrary numbers. Each one is matched to a boost level, 30 V, 55 V, 80 V and 105 V, so the input stays inside a 1.8 V peak window at full output. Choosing a gain that does not match the boost rail either wastes resolution or clips the waveform, and the vendor pairs them in the gain bandwidth curves.
Slew rate runs from 150 V per ms at the lowest gain to 600 V per ms at the highest, bandwidth falls from 20 kHz at 50 V peak to peak to 5 kHz at 200 V peak to peak, and the gain bandwidth product is 550 kHz. Input noise is 6.5 uV per root hertz, common mode rejection is 100 dB and supply rejection is 60 dB, which is what allows a piezo to be driven from a switching rail without the ripple appearing in the mechanical output.
Key data for the DRV2700RGPR
| Supply | 3.3 V to 5.5 V on the logic and switch side, boost output set by two external resistors |
| Output | Plus and minus 100 V in boost plus amplifier configuration, up to 1 kV in flyback configuration |
| Gain | 28.8 dB, 34.8 dB, 38.4 dB and 40.7 dB, paired with 30 V, 55 V, 80 V and 105 V boost levels |
| Bandwidth | 20 kHz at 50 V peak to peak, 10 kHz at 100 V, 7.5 kHz at 150 V, 5 kHz at 200 V |
| Slew rate | 150 V per ms to 600 V per ms depending on the gain setting |
| Current | 5 uA shutdown, quiescent 5 mA at a 30 V boost rising to 24 mA at 105 V, no signal |
| Start up | 1.5 ms typical from enable high to boost and amplifier both running |
| Protection | Thermal overload protection, programmable boost current limit through one resistor |
Body, packing and marking data
| Body | VQFN RGP, 20 pins, 4 mm by 4 mm by 0.9 mm |
| Packing | 3000 pieces on a large reel as DRV2700RGPR, 250 pieces on a small reel as DRV2700RGPT |
| Finish | NIPDAU, moisture level 1, 260 C peak, unlimited floor life |
| Temperature | Minus 40 C to plus 85 C, 33.1 C per W junction to ambient in still air |
Order code note before you place the string on a purchase order
The R and the T at the end of this pair are the large reel and the small reel, and both are printed as active production with NIPDAU at moisture level 1. The marking on both is DRV2700, which is longer than the space on a 4 mm package usually allows, so the mark to compare at goods inwards is the full string rather than a short code.
Two external choices decide whether the part does what the circuit around it expects. The boost level comes from the feedback divider, and the gain pins have to be strapped to match it. A board that leaves the two gain pins floating will run at one of the four settings by accident, and the symptom is a waveform that clips on one rail before the expected amplitude. Strap them to a defined level even when only one gain is used.
Where a piezo driver with an internal boost earns its place
Piezo positioning stages, sounders, inkjet heads, micropumps and high voltage haptic elements all need a rail far above the logic supply and a waveform that can be shaped. Putting the boost inside the driver removes the separate converter, its inductor and the sequencing question of which rail comes up first, and the 1.5 ms start up means the actuator can move within the first few milliseconds after a wake event.
A high voltage stage changes what the rest of the board has to withstand, and that is a sourcing question as much as a circuit one. Our strategic sourcing page covers grouping the high voltage passives with the driver, and the one stop BOM sourcing page is the place to start when the inductor and the transformer have to come from a supplier that can also hold the rest of the board.
Questions we get on this code
The first question is whether the 100 V figure is peak to peak or from rail to rail. It is plus and minus 100 V relative to the mid point in the differential configuration, so the swing across the load is 200 V peak to peak, and the amplifier bandwidth figures in the data sheet are quoted at that swing.
The second question is about the flyback route. Above about 100 V the boost topology runs out and the inductor has to be replaced by a transformer, which brings a rectifier and a different current limit calculation with it. The vendor split the two configurations into separate application sections, and the external components are not interchangeable between them.