DRV5032AJDBZR
Product Specifications
DRV5032AJDBZR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5032AJDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5032AJDBZR: a 9.5 mT switch that draws microamps
The DRV5032AJDBZR is a digital Hall switch built for battery powered products. Average supply current on the 20 Hz versions of this family is 1.3 uA, the supply window is 1.65 V to 5.5 V, and the body is the three pin SOT-23. The AJ option has a 9.5 mT maximum threshold and an open drain output, sampled at 20 Hz.
The mechanism behind the current figure is duty cycling. An internal oscillator wakes the Hall element, takes a sample, updates the output and goes back to sleep, so the part is not biased continuously. Sampling at 20 Hz means the field is read every 50 ms, which sets the fastest event the part can catch.
That sampling rate is the number to plan the mechanics around. A magnet that passes the sensor in 10 ms can be missed entirely at 20 Hz, and the data sheet says so in the same table where it lists the current. Choosing between the 80 Hz, 20 Hz and 5 Hz versions is a choice between current and event rate, not a matter of preference.
Key data for the DRV5032AJDBZR
| Output | Open drain on the AJ option, active low above the threshold |
| Threshold | 9.5 mT maximum operate point, omnipolar response |
| Sampling rate | 20 Hz, so one reading every 50 ms |
| Supply current | 1.3 uA average on the 20 Hz versions, 5.2 uA on the 80 Hz version |
| Supply | 1.65 V to 5.5 V, which covers a single lithium cell without a boost |
| Temperature | Minus 40 C to plus 85 C across the whole family |
| Response | Output updates on the sampling edge, so latency is one sample period |
Body, packing and marking data
| Body | SOT-23, three pins, DBZ outline |
| Packing | 3000 pieces on a large reel |
| Finish and moisture | Tin lead finish, moisture level 1 at 260 C, unlimited floor life |
| Marking | 1M6W and 2AJ on the body, which is how the AJ die is identified on a mixed reel |
How the code divides the family
The code reads DRV5032, then a two letter version, then the body, then the packing. AJ is the 9.5 mT open drain omnipolar version, ZE is the 63 mT open drain part for strong fields, and the DG, DU, FA, FB, FC and FD versions cover 3.4 mT to 4.8 mT in push-pull and open drain forms at 5, 20 and 80 Hz.
The body field matters more here than on the other Hall parts, because this family ships in three shapes. DBZ is the SOT-23, DMR is the four pad X2SON at 1.5 mm by 1 mm, and LPG is the TO-92. The AJ version is published in all three, with the TO-92 in ammo and bulk and the X2SON rows partly obsolete.
Two rows on the addendum are already obsolete: the X2SON T suffix for AJ and the A revision of the X2SON DU part. A board that was qualified on one of those needs a last time buy or a move to the active row rather than a new schedule.
Where a microamp switch earns its place
Battery critical position sensing, electricity meter tamper detection, and lid or flip detection on a phone, laptop or tablet are the three uses the vendor names. In each of them the sensor is powered from a coin cell or a supercapacitor and has to survive years of standby, so the 1.3 uA average is the whole reason the part exists.
Where the board also carries a battery gauge in the same enclosure, the safety stock planning page is worth a look before the sensor goes into a long life product, and the date code management page covers what to check on a reel that will sit in stores for a year.
Questions we get on this code
Why does the part miss a fast magnet? Because it samples. The 20 Hz version looks at the field 20 times a second, so an event shorter than a sample period can fall between two readings. On a tamper switch that is fine, on a gear tooth counter it is not, and that is when the 80 Hz version is the right part even though it draws four times the current.
The second question is about the open drain output on a 1.8 V rail. The output is a switch to ground, so the pull up can go to the controller rail whatever the sensor supply is, and the only limit is the 20 mA sink the output can take. Leaving the pull up off entirely is the most common assembly error on this family.
A third point is the supply ramp. The part has no brownout detector of its own, so a rail that crawls up over several hundred milliseconds leaves the output in an undefined state until the first sample is taken. On a product that reads the lid state in the first millisecond after reset, the controller has to wait for one sample period before it trusts the pin.